IMPRESSA E40
IMPRESSA E60
IMPRESSA E65
Instructions for use
02/02
Fig. 1
Fig. 4
Fig. 7
Fig. 2
Fig. 5
Fig. 8
Fig. 3
Fig. 6
Fig. 9
2
1
Operating elements
Jura Impressa E40/E60/E65
1 Water quantity switch
2 Powder coffee selection switch
3 Coffee key for 2 cups
9
10
11
4 Maintenance key (for functions such as: rinsing,
cleaning, de-scaling, filter)
5 Coffee key for 1 cup
8
7
6 ON/OFF switch
7 Display with symbols
12
8 Water tank with carrying handle
9 Height-adjustable coffee spout
10 Pre-ground coffee filler funnel
11 Cover for beam container
12 Selector switch for hot water/steam
13 Pivoting nozzle for hot water/steam
14 Frothing aid
6
5
4
3
2
1
13
14
15 Container for coffee grounds
16 Drip tray cover
17 Drip tray
15
16
17
Contents
Jura Impressa E40/E60/E65
1. Description ..................................................page
1.1 The symbols mean ..................................page
2. Safety instructions........................................page
2.1 Warnings ..............................................page
2.2 Safety precautions..................................page
3. Preparation of the machine ............................page
3.1 Checking the mains voltage .....................page
3.2 Checking the fuse ..................................page
3.3 Filling the water tank..............................page
3.4 Adding coffee beans ...............................page
3.5 Adjusting the grinder..............................page
3.6 Adjusting the water hardness ...................page
3.7 Adjustable automatic switch-off................page
4. First start of operation..................................page
4.1 Fill system with water .............................page
6
6
7
7
7
7
7
7
7
7
8
8
9
9
9
10. Switching machine off...................................page 11
11. Care and maintenance ...................................page 12
11.1 Fill water ..........................................page 12
11.2 Empty grounds container......................page 12
11.3 No drip tray........................................page 12
11.4 Clean unit ..........................................page 12
11.5 Unit scaled .........................................page 12
11.6 Use of Claris filter cartridges ................page 12
11.7 Insert filter.........................................page 12
11.8 Replace filter......................................page 13
11.9 General cleaning instrictions..................page 13
11.10 Regular service....................................page 13
11.11 Empty system .....................................page 14
12. Cleaning......................................................page 14
13. Decalcifying.................................................page 15
14. Disposal ......................................................page 16
15. Tips for perfect coffee...................................page 16
16. Messages.....................................................page 17
17. Problems.....................................................page 18
18. Legal information .........................................page 19
19. Technical data..............................................page 19
E
5. Rinsing the machine......................................page 10
6. Adjusting the water quantity..........................page 10
7. Drawing off espresso/normal coffee .................page 10
7.1 Drawing off espresso/strong coffee............page 10
7.2 Drawing off espresso/extra coffee..............page 10
7.3 Drawing off powder coffee.......................page 10
8. Drawing off steam ........................................page 11
8.1 Return to stand-by .................................page 11
9. Drawing off hot water ...................................page 11
5
1.1 The symbols mean
Important information for the user
1 COFFEE READY
2 COFFEE POWDER
3 RINSE MACHINE
4 STEAM / HOT WATER
5 CLOSE TAP
Thank you for choosing this Jura product.
Please study these instructions carefully before using your new
machine for the first time and keep them in a safe place for easy
reference in future.
Should you require further information or should particular
problems occur that are not dealt with in sufficient detail for you in
these operating instructions, please contact your local dealer or us
for the information you require.
6 FILL WATER
7 EMPTY GROUNDS CONTAINER /
DRIP TRAY MISSING
8 CLEAN MACHINE
9 MACHINE SCALED
10 REPLACE FILTER
11 OPEN TAP
4
2
3
1
5
b
b
b
1. Description
This fully automatic espresso/coffee machine impresses because of
its compactness and can prepare 1 or 2 cups of excellent, profes-
sional-quality espresso/coffee with guaranteed froth. The unique
Jura pre-brew system (Intelligent Pre Brew Aroma System
I.P.B.A.S©) ensures full use of the coffee aroma. The machine
works fully automatically at the push of a button. With the coffee
aroma, you have the choice between normal, strong and extra
strong, depending on taste. The integrated grinder grinds the beans
to the required fineness. A separate filler funnel makes it possible
to use additional, pre-ground sorts of coffee. The water quantity
can be set individually. Electronic filling controls for the water
tank and container for coffee grounds simplify operation. Thanks to
the integrated rinsing, cleaning and de-scaling programmes, care
and maintenance are also quick and easy.
8
11
6
7
9
10
6
2. Safety instructions
2.1 Warnings
Ⅲ If you use de-scaling agents containing acid, remove any splas-
hes and drips on sensitive surfaces, in particular natural stone
and timber surfaces and/or take corresponding precautionary
measures.
Ⅲ Children are unaware of the dangers that electrical machines can
represent; for this reason, children should never be left unsuper-
vised with electrical machines.
3. Preparation of the machine
3.1 Checking the mains voltage
Ⅲ This machine should only be used by people who have read
these instructions.
The machine is set to the correct voltage before leaving our
factory. Ensure that your mains voltage corresponds to the details
quoted on the rating plate attached to the bottom of the machine.
Ⅲ Never use a faulty machine or one with a damaged power cable.
Ⅲ Never immerse the machine in water.
2.2 Safety precautions
3.2 Checking the fuse
Ⅲ Never subject the machine to the effects of the weather (rain,
snow, frost) and never operate it with wet hands.
The machine is designed for a current of 10 Amps. Check that the
fuse used matches this.
Ⅲ Place your machine on a solid level surface. Never leave it on a
surface which is warm or hot (hob etc.). Choose a location which
is inaccessible for children or for pets.
3.3 Filling the water tank
E
Ⅲ Remove the water tank and rinse it out well with cold tap water.
Ⅲ Always pull the plug out if you are away for a long time (holi-
days etc.).
Ⅲ Then fill the water tank and put it back into the machine. Ensure
that the tank engages properly (Fig. 1).
Ⅲ Always pull the plug out first before cleaning.
Ⅲ When pulling the plug out, never tug on the cord or on the
machine itself.
Only use fresh, cold water. Never fill with milk, mineral
water or other fluids. You can also add water without
removing the tank. Simply lift the lid up and pour in water
from above with a vessel. Close the lid again.
Ⅲ Never repair or open the machine yourself. All repairs should be
done by authorised service centres only using original Jura spare
parts and accessories.
Ⅲ The machine is connected to the mains power socket via an
electric cable. Make sure that nobody trips over it and pulls the
machine down. Keep children and pets well away from the
machine.
3.4 Adding coffee beans
Ⅲ Lift up the cover of the bean container (11).
Ⅲ Clean out any dirt or foreign objects from the bean container.
Ⅲ Never put the machine or even parts of it into the dishwasher.
Ⅲ Pour coffee beans into the bean container and close the cover
again.
Ⅲ Choose a place with a good circulation of air in order to prevent
the machine from overheating.
7
3.5 Adjusting the grinder
The machine has 6 hardness settings to choose from. During the
setting, the water hardness selected is shown on the display.
You have the possibility of adjusting the grinder to the roast of
your coffee. We recommend the following:
for a light roast © a finer adjustment
for a dark roast © a coarser adjustment
Level for Claris Filter
Setting for the use of the Claris filter
cartridge.
Ⅲ Open the cover of the bean container.
Ⅲ To adjust the grinding, turn the selector switch (Fig. 2) to the
required position.
Level 0 = water hardness is switched off
The automatic scale display is
switched off.
Ⅲ You have the following possibilities:
the smaller the dots, the finer the grinding
the larger the dots, the coarser the grinding
the degree of grinding should only be adjusted with the
grinder in operation.
Level 1
German water hardness 1 – 7°
French water hardness 1.79 – 12.53°
3.6 Adjusting the water hardness
Water is heated inside the machine. This leads to calcium deposits
(scale) during use. This is automatically displayed.
Before you use your machine for the first time, you must adjust it
to the hardness of the local water. For this purpose, please use the
enclosed test sticks.
Level 2
German water hardness 8 – 15°
French water hardness 14.32 – 26.85°
Level 3
1° German water hardness corresponds to 1.79° French water
hardness.
German water hardness 16 – 23°
French water hardness 28.64 – 41.14°
Level 4
German water hardness 24 – 30°
French water hardness 42.96 – 53.7°
The machine is adjusted to hardness level 3 in the factory. You
can alter this setting by proceeding as follows:
8
Ⅲ Pull the plug and the feed wire out of the wire box on the back
of the machine.
In order to set or alter the automatic switch-off time, please
proceed as follows:
Ⅲ Put the plug in.
Ⅲ Connect the plug with the mains.
Ⅲ Do not switch the machine on.
Ⅲ However, do not switch the machine on.
Ⅲ Press the
draw-off key for about 3 seconds. Now, the
symbols light up.
Ⅲ Please the
symbols light up.
Ⅲ Select the required level with the
Ⅲ Press the ON/OFF switch in order to save the required level.
draw-off key for about 3 seconds. The
,
,
,
,
,
Ⅲ Now select the corresponding level with the
and press the ON/OFF
The symbols go off.
draw-off key
switch in order to save the setting.
draw-off key.
If you do not carry out a change of level for longer than 30
seconds, the display goes off. The last figure you have stored
remains valid.
The water hardness only need to be set before the first use of
the machine or if a different water quality is used.
If you do not carry out a change of level for longer than 30
seconds, the display goes off. The last figure you have stored
remains valid.
4. First start of operation
4.1 Fill system with water
3.7 Adjustable automatic switch-off
Ⅲ Switch your machine on with the ON/OFF
Ⅲ The symbol lights up.
switch.
E
You can amend the automatic switch-off time of 1 1/2 hours set by
Jura. The machine offers you three levels for this:
Ⅲ Place an empty cup under the pivoting nozzle for hot water/
steam (13).
1st level
Ⅲ Switch the selector switch for hot water/steam (12) to the
position. The machine now lets off water and the
flashes at the same time.
The
symbol lights up. The automatic switch-off is not acti-
symbol
vated.
Ⅲ If the
symbol lights up on the display, turn the selector
position.
2nd level
switch for hot water/steam (12) back to the
The
,
,
symbols light up.
The automatic switch-off is set to 1 1/2 hours.
3rd level
The
,
,
,
,
,
symbols light up.
The automatic switch-off is set to 3 1/2 hours.
9
5. Rinsing the machine
In order to obtain outstanding froth, you can adapt the
coffee-spout (5) individually to the size of your cups (Fig. 3).
When the
symbol lights up, a rinsing process is demanded.
Ⅲ Place an empty cup under the coffee-spout.
7.1 Drawing off espresso/strong coffee
Ⅲ Press the rinsing maintenance key (4). The rinsing process is
Ⅲ Place 1 cup under the coffee-spout (9).
automatically ended.
Ⅲ Press the
of the
draw-off symbol until two dots light up to the left
symbol.
If the machine has been switched off and has already cooled
down, the rinsing function will be demanded when the
machine is switched on.
A rinsing is automatically started when the machine is
switched off.
This draw-off of espresso / strong coffee is only possible for
1 cup.
7.2 Drawing off espresso/extra coffee
6. Adjusting the water quantity
Ⅲ Place 1 cup under the coffee-spout (9) .
The water quantity can be infinitely adjusted with rotary knob (1).
The small key means little water for espresso, the large cup means
a lot of water for coffee.
Ⅲ Press the
left of the
draw-off symbol until three dots light up to the
symbol.
This draw-off of espresso / extra coffee is only possible for
1 cup.
You can also change the water volume while coffee is being
drawn off. Simply turn the rotary knob (1) to give more or
less water.
7.3 Drawing off powder coffee
With draw-off key
the water quantity and distributes it to 2 cups.
, the machine automatically doubles
Ⅲ Press the
selector switch. The
and
symbols light
up.
Ⅲ Now put 1 or 2 level measuring spoons of pre-ground coffee into
the filler funnel for pre-ground coffee (10).
7. Drawing off espresso/normal coffee
Ⅲ As soon as the
symbol lights up, you can draw off coffee.
Ⅲ Place 1 or 2 cups under the coffee-spout (9) and press the
required coffee key.
Ⅲ Place 1 or 2 cups, as necessary, under coffee-spout (9) and press
the required draw-off key. The pre-brew system (I.P.B.A.S.©)
moistens the coffee powder, briefly interrupts the flow and then
starts the actual brewing process.
Never use water-soluble instant coffee or quick coffee. We
recommend that you only use powder from freshly ground
coffee beans or pre-ground, vacuum-packed coffee. Never
put more than 2 portions of coffee in. The filler funnel is
not a storage container.
You can interrupt the draw-off prematurely by pressing any
of the coffee draw-off keys.
10
8.1 Return to stand-by
If the
draw-off key is pressed by mistake, the selection
can be cancelled by pressing the
machine rinses.
draw-off key. Your
Ⅲ Place a vessel under the pivoting nozzle for hot water/steam
(13).
Ⅲ Press a draw-off key, the
symbol lights up on the display.
After drawing off powder coffee, we recommend that you
regularly clean the filler funnel with a clean bottle-cleaning
brush.
Ⅲ Turn the selector switch for hot water/steam (12) to the position
.
Ⅲ Draw water off until the flow of water is automatically inter-
rupted and the
Ⅲ After this, turn the selector switch for hot water/steam (12) back
to the position.
symbol lights up.
8. Drawing off steam
The steam can be used for heating liquids and also for frothing
milk for cappuccino. Make sure that the frothing aid (14) is pushed
upwards when heating liquids. When frothing liquids, push the
frothing aid downwards (Fig. 5).
After each steam draw-off, clean the pivoting nozzle with a
damp cloth.
Ⅲ Place a cup under the pivoting nozzle for hot water/steam (13).
Ⅲ Immerse the frothing aid (14) into the milk to be frothed or the
liquid to be heated and turn the selector switch for hot
9. Drawing off hot water
water/steam (12) to the
position.
Ⅲ Place a cup under the pivoting nozzle for hot water/steam (13)
and turn the selector switch for hot water/steam (12) to the
E
Ⅲ Immediately after this, press the maintenance key (4).
symbol
.
Ⅲ When you have reached the required quantity of steam, turn the
selector switch for hot water/steam (12) back to the position
Ⅲ The machine now produces hot water.
.
Ⅲ To finish the process, turn the selector switch for hot water/
Ⅲ The symbols light up.
,
steam (12) back to the
position.
Ⅲ If you would like to draw off a coffee immediately after the
steam, please proceed as described in point 8.1.
At the start of a water draw-off, there can be splashes. The
pivoting nozzle for hot water/steam gets hot. Please avoid
direct contact with the skin.
The max. draw-off time is about 8 minutes.
A little water will come out first when frothing. It can be let
off before actually drawing off steam. The good result, e.g.
when frothing milk, is not influenced in any way.
10. Switching machine off
When the machine is switched off, the rinsing programme is auto-
matically started. Therefore, place an empty container under the
At the start of a steam draw-off, there can be splashes. The
pivoting nozzle for hot water/steam gets hot. Please avoid
direct contact with the skin.
coffee-spout and press the ON/OFF
switch.
When the rinsing water has run into the cup, the machine switches
off. Throw the rinsing water away.
11
11. Care and maintenance
11.1 Fill water
11.4 Clean unit
After 200 draw-offs or 160 rinses, the machine must be cleaned;
the
symbol flashing announces this. You can continue to draw
Ⅲ When the
display lights up, no drawing-off is possible. Fill
off coffee or hot water/steam. We recommend carrying out the
cleaning (as described in point 12) within the next few days.
with water as described under point 3.3.
Warning lamp
does not go out until the complete cleaning
prozess has been carried out.
11.2 Empty grounds container
The grounds container collects the coffee grounds. When this dis-
11.5 Unit scaled
play
lights up, no drawing-off is possible and the grounds
container must be emptied.
Scale is caused by using the machine and depends upon the hardness level
of your water. The machine recognises the necessity of de-scaling. Here
too, the flashing symbol tells you when de-scaling is necessary.
You can continue to draw off coffee or hot water/steam. We re-
commend carrying out the de-scaling (as described in point 13)
Ⅲ Push the coffee spout (9) up.
Ⅲ Remove the drip tray. Be careful, as there is water in it.
Ⅲ Empty and clean the drip tray and the grounds container (Fig. 6).
Push the drip tray and then the grounds container back in
(Fig. 7).
within the next few days. Warning lamp
does not go out until
the complete decalcifying prozess has been carried out.
The drip tray must also be emptied when you empty the
grounds.
11.6 Use of Claris filter cartridges
If the Claris filter cartridges are used correctly, your machine no
longer needs de-scaling. You can obtain more information from the
brochure “Claris. Hard on scale. Gentle to your coffee machine.”
(enclosed in the welcome pack).
11.3 No drip tray
If the
symbol flashes, the drip tray has not been inserted
properly.
11.7 Insert filter
If the drip tray has not been put into the machine, you can
clean the interior of the machine. Wipe out any coffee
powder that might be in the machine with a damp cloth. Put
the drip tray back in again.
Ⅲ Pull up the cartridge holder in the water tank. Pressing gently,
put the filter cartridge into the water tank (Fig. 4).
Ⅲ Close the cartridge holder until it engages audibly.
Ⅲ Fill the water tank with cold fresh tap water and put it back into
the machine.
12
Ⅲ Place a sufficiently large vessel under the pivoting nozzle for
hot/water steam (13) and turn the selector switch for hot
Ⅲ Switch the machine on with the ON/OFF
Ⅲ Press the draw-off key for about 3 seconds. The degree of
hardness set appears on the display.
switch.
water/steam (12) to the position . The
Ⅲ Draw off water until the symbol lights up.
Ⅲ Now turn the selector switch for hot water/steam (12) back to the
symbol flashes.
Ⅲ Press the
draw-off key until only the
symbol is still
alight.
position
.
Ⅲ Press the ON/OFF
switch as a confirmation. The
,
Ⅲ When the
symbol lights up, press the maintenance key (4).
symbols light up.
Your machine rinses and is ready for drawing off coffee.
Ⅲ Place a sufficiently large vessel under the pivoting nozzle for hot
water/steam (13) and turn the selector switch for hot water/
steam (12) to the position
.
11.9 General cleaning instructions
Ⅲ Draw off water until the
symbol lights up.
Ⅲ Never use abrasive articles or corrosive chemicals to clean your
machine.
Ⅲ Now turn the selector switch for hot water/steam (12) back to the
position
.
Ⅲ Wipe down the casing on the inside and out using a soft, damp
cloth.
Ⅲ When the
symbol lights up, press the maintenance key (4).
Your machine rinses and is ready for drawing off coffee.
Ⅲ Clean the pivoting nozzle for hot water/steam after each use.
Ⅲ After heating milk, draw off a little hot water in order to clean
the inside of the pivoting nozzle.
The water can be slightly discoloured (not dangerous to
health)
E
Ⅲ You can take off the frothing aid for a thorough cleaning
(Fig. 8).
11.8 Replace filter
Ⅲ The water tank should be rinsed out and filled with clean water
every day.
After 50 litres have been drawn off, the filter loses its effect.
The symbol flashes to inform you.
If there is scale visible in the water tank, you can remove it
with a customary de-scaling agent. Remove the water tank
from the machine for this purpose.
If you do not draw off often, you should replace the filter
cartridge every 2 months, but no report appears on the dis-
play. There is a special disk on the cartridge holder so that
you can set the replacement date.
11.10 Regular service
Regular inspections by Jura Service extend the service life and
reliability. Keep the original packaging as transport protection.
Ⅲ Switch your machine off with the ON/OFF
switch.
Ⅲ Press the maintenance key (4) for about 3 seconds. The
,
symbols light up.
13
11.11 Empty system
Ⅲ Press the maintenance key (4) for about 3 seconds. The
(only
when necessary),
,
symbols light up.
This procedure is necessary in order to protect the machine
from damage by frost in transport.
Ⅲ Fill the water tank.
Ⅲ Empty the drip tray and the grounds container and put both of
them back in again. The (only when necessary), symbols
go off and the symbol appears.
Ⅲ Please a vessel under the coffee spout (9) and press the mainten-
ance key (4). The symbol goes off.
Ⅲ Switch the machine OFF with the ON/OFF
switch.
Ⅲ Place a vessel under the pivoting nozzle for hot water/steam
(13).
Ⅲ Turn the selector switch for hot water/steam (12) to position
.
Ⅲ Switch your machine back on again with the ON/OFF
The
symbol lights up to inform you that the cleaning process
switch. The
symbol lights up.
has been activated.
Ⅲ Press the maintenance key
until the symbol
flashes.
.
Ⅲ Draw steam off until the flow of steam is automatically inter-
rupted and the symbol lights up on the display.
Ⅲ After this, turn the selector switch for hot water/steam (12) back
to the position.
Ⅲ If the
put it back in again. The
symbols light up.
symbol lights up, empty the drip tray (if necessary) and
symbol goes off and the
,
,
Ⅲ Now put a Jura cleaning tablet into the filler funnel for powder
coffee (10) (Fig. 9).
Ⅲ Press the maintenance key (4). The
,
symbols go off.
12. Cleaning
The machine has an integrated cleaning programme.
The cleaning process is continued. This is displayed by the
symbol lighting up.
If the machine needs cleaning, the
symbol flashes.
You can continue to draw off coffee or hot water/steam and
run the cleaning programme later.
Ⅲ If the
sary), wait for about 10 seconds before putting it back in again.
The symbol goes off and the symbols light up.
symbol lights up again, empty the drip tray (if neces-
,
Only use Jura cleaning tablets. They are available from your
Jura dealer.
Ⅲ Place a vessel under the coffee spout (9) again and press the
maintenance key (4).
You must not interrupt the cleaning programme once it has
started.
Ⅲ The cleaning process is continued. This is displayed by the
symbol lighting up. As soon as it has been completed, the
symbol lights up.
Ⅲ Switch your machine on with the ON/OFF
key.
14
Ⅲ Empty the drip tray and the grounds container and put both of
them back in. The symbol lights up.
Ⅲ Turn the selector switch for hot water/steam (12) to the position
. The symbol go off and the symbols light up.
,
Ⅲ Place a sufficiently large vessel under the pivoting nozzle for hot
water/steam (13) and press the maintenance key (4).
After each cleaning operation the filler funnel for the 2nd
coffee type should be cleaned.
The lighting of the symbol and the flashing of the
show you that the de-scaling process has been activated.
symbol
13. Descalcifying
The machine has an integrated de-scaling programme. If you use a
Claris filter cartridge, your machine does not need de-scaling. Only
use Jura cleaning tablets. They are available from your Jura dealer.
Ⅲ If the
put it back in again. The
Ⅲ Turn the selector switch for hot water/steam (12) back to the
position
symbol lights up, empty the drip tray (if necessary) and
symbol lights up.
.
If the machine needs de-scaling, the symbol flashes.
You can continue to draw off coffee and hot water/steam and
then run the de-scaling programme later.
The de-scaling process is continued de-scaling solution is guided
into the drip tray in the interior of the machine.
Only run the de-scaling programme when the machine has
been switched off for at least 2 hours and has cooled down
well. The de-scaling programme is started with the machine
switched off. Once it has started, the de-scaling programme
must not be interrupted.
Ⅲ The
,
,
symbols light up.
Rinse the water tank out well and fill it with cold fresh
tap water. Then put it back into the machine again. Place a
sufficiently large vessel under the pivoting nozzle.
E
Ⅲ Switch your machine off with the ON/OFF
it to cool down for 2 hours.
switch and leave
Ⅲ Empty the drip tray and put it back in again. The
light up.
,
symbols
Ⅲ Remove the water tank and empty it.
Ⅲ Turn the selector switch for hot water/steam (12) to position
.
Ⅲ Press the maintenance key (4) for about 3 seconds. The
symbols light up.
,
Ⅲ Place a sufficiently large vessel under the pivoting nozzle for hot
water/steam (13) and press the maintenance key (4).
Ⅲ Empty the drip tray and the grounds container and put both of
them back in again. The
symbols light up.
symbol goes off and the
,
The lighting of the symbol and flashing of the
you that the de-scaling process has been activated.
symbol show
Ⅲ Completely dissolve the contents of one blister (2 tablets) in 0.5
litres of water in a vessel and pour the mixture into the water
Ⅲ If the
,
,
symbols light up, empty the drip tray (if neces-
sary) and put it back in again.
tank. Put the tank back in again. The
symbol appear.
15
Ⅲ Turn the selector switch for hot water/steam (12) back to the
position
.
The de-scaling process is continued and the water is guided into
the drip tray in the interior of the machine.
Ⅲ If the
again. The
symbol lights up, empty the drip tray and put it back in
symbol appear.
Ⅲ After this, press the maintenance key (4). Your machine rinses
and is now ready for the next draw-off of coffee.
14. Disposal
For correct disposal, you should return your coffee machine to your
dealer, your Jura service centre or the firm of Jura.
15. Tips for perfect coffee
Height-adjustable coffee-spout
You can adjust the coffee-spout to the size of your cups
Grinding
See point 3.5
Pre-warming cups
You can pre-warm the cups with hot water or steam. The smaller
the amount of coffee, the more important the pre-warming.
Sugar and cream
Heat is lost by stirring the contents. Adding milk or cream from the
fridge considerably lowers the temperature of the coffee.
16
16. Messages
Display
Cause
Action
– System empty
– Fill system (see point 4.1)
– Reset to coffee stand-by
– System too hot after drawing off steam
– Wrong position of selector switch
– Put selector switch into correct position
– General troubles
1. – Switch off
b
b
b
– disconnect from mains
– connect to mains
– switch machine on
2. Have machine examined by Jura service
centre
E
– Machine needs rinsing
Rinsing the machine
– The tank is empty
– Floater defective
– Fill with water
– Rinse out or de-scale water tank
– Grounds container full
– Empty grounds container
– Tray replaced too early after emptying
– Only replace the tray after about 10 sec.
17
Display
Cause
Action
– Drip tray not inserted properly or missing
– Insert correctly
flash
– Cleaning necessary
– De-scaling necessary
– Replacing of filter
– Carry out cleaning process
– Carry out de-scaling process
– Run program
flash
flash
flash
17. Problems
Problem
Cause
Action
Coffee flow is stopped
after pre-brewing
– bean container empty
– not enough coffee powder
– foreign body in grinder
– Fill with beans
– Correct amount of powder
Grinder is very noisy
– Drawing off coffee with pre-ground powder
– is still possible
– Have machine examined by Jura service centre
18
Problem
Cause
Action
Not enough froth when
frothing milk
– milk not suitable
– frothing aid blocked
– frothing aid in wrong position
– use full-cream milk
– clean frothing aid
– draw off steam (see point 8)
If the above mentioned messages and/or problems still exist, please contact your dealer or get in touch directly with Jura Elektroapparate
AG.
18. Legal information
19. Technical data
These operating instructions contain the information necessary for
the correct use, operation and maintenance of the machine.
Understanding of and complying with the directions contained in
these operating instructions are essential for use of the machine
without risk and for safety in operation and maintenance.
The operation instructions cannot cover every imaginable example
of use. The machine has been designed for use in private house-
holds.
We would further like to point out that the contents of these ope-
rating instructions in no way constitute a part or, nor do they alter
any previous or existing contract, assurance or legal relationship.
All obligations on the part of Jura Elektroapparate AG result from
the purchase contract in question, which also contains full details
of the only warranty regulations applying to this machine. These
contractual warranty terms are neither extended nor limited by the
information given in these operating instructions.
Voltage:
Output:
230V AC
1350 W
10 A
E
Fuse:
Safety check:
Energy consumption standby: approx. 4Wh
Energy consumption ready to
make coffee:
approx. 17Wh
max. 15 bar
1,9 litres
Pump pressure:
Water tank:
Capacity, bean container:
200 gr.
Capacity, grounds container: max. 16 port.
The operating instructions contain information protected by copy-
right. Photocopying or translating into another language shall not
be admissible without prior written approval by Jura Elektroap-
parate AG.
Cable length:
1,1 m
Weight:
8,3 kg
Dimensions (B x H x D):
28 x 34,5 x 41,5 cm
19
|