CD-RECEIVER
KDC-BT50U
KDC-5047U
KMR-440U
INSTRUCTION MANUAL
Before reading this manual, click the button below to check the latest edition
and the modified pages.
Check the latest edition
© 10Stepup_IM304_Ref_En_03_E
Before use
Notes
2WARNING
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
• Characters that conform to ISO 8859-5 or ISO 8859-
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Exit Demonstration
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
How to reset your unit
• If the unit fails to operate properly, press
the Reset button. The unit returns to factory
settings when the Reset button is pressed.
Reset button
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
clean soft dry cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with a neutral cleaner, then wipe it
again with a clean soft dry cloth.
Applying spray cleaner directly to the unit may affect
its mechanical parts. Wiping the faceplate with a
hard cloth or using a volatile liquid such as thinner or
alcohol may scratch the surface or erase characters.
CDs that cannot be used
• CDs that are not round cannot be used.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-R/
CD-RW recorder instruction manual.)
Unit and Faceplate Terminals
• To prevent deterioration, do not touch the terminals
of the unit and faceplate with your fingers.
.
• If the terminals on the unit or faceplate get dirty,
wipe them with a clean soft dry cloth.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• 3 inch CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
English
|
3
Basic Operations
KDC-BT50U
[
] [SRC]
[
]
USB Terminal
0
Release Microphone
Disc slot
KDC-5047U KDC-5047U
Control
Knob
KMR-440U
[DISP]
KDC-BT50U KDC-BT50U
KMR-440U
[AUDIO]
Auxiliary input
[
] [FNC]
[ENTER] [FAVORITE]
[
]
[
]
Before Using
Common Operation
Exit Demonstration Mode
Power and source selection
Turn off the demonstration mode when you use it
for the first time after installation.
Turns the power ON by pressing the [SRC]
button.
When the power is ON, select a source.
Press the [SRC] button and then turn the Control
knob. To determine the selected source, press the
[ENTER] button.
1 Press the [ENTER] button to quit the
demonstration mode when the messages “To
Cancel DEMO Press the ENTER Key” are displayed
(approx. 15 seconds).
Tuner (“TUNER”) ➜ Bluetooth Audio (“BT AUDIO”)
(KDC-BT50U only) ➜ USB (“USB”) or iPod (“iPod”)
➜ CD (“CD”) ➜ Auxiliary Input (“AUX”) ➜ Standby
(“STANDBY”) ➜ Tuner...
Press the [SRC] button for at least 1 second to
turn the power OFF.
2 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
The demonstration mode can also be canceled
Adjusting the Date
1 Press the [FNC] button to enter the Function
setting mode.
⁄
• You can select the source selection mode to switch
between sources each time you press the [SRC] button. Set
• The source “iPod” and “CD” can be selected when each
source is ready to play.
• When an optional accessory is connected, the source name
for each device appears.
• The power will be turned off automatically after about 20
minutes have lapsed in standby mode. (KMR-440U only)
2 The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
3 Turn the Control knob to adjust the year, and
then press the [ENTER] button.
Volume
4 Turn the Control knob to adjust the month, and
then press the [ENTER] button.
Turn the Control knob to adjust the sound
volume.
5 Turn the Control knob to adjust the day, and then
press the [ENTER] button.
Display scroll
KDC-5047U KMR-440U
Keep the [DISP] button pressed down to scroll
through the CD, audio file, or Radio text display.
KDC-BT50U
then press the [ENTER] button.
7 Turn the Control knob to select Date format, and
then press the [ENTER] button.
Keep the Control knob pushed towards up to
scroll through the CD, audio file, or Radio text
8 Press the [
] button for at least 1 second to
exit the Function setting mode.
|
4
KDC-BT50U/ KDC-5047U/ KMR-440U
display.
Auxiliary input
Portable audio device can be connected with the
stereo mini-plug (3.5 mm ø).
Listening to Radio
Selecting a Tuner source
1 Press the [SRC] button.
Playing Music (CD/USB/iPod)
2 Turn the Control knob to select “TUNER”, and
Playing Disc
then press the [ENTER] button.
Insert the disc in the Disc slot.
When inserted, the source is switched
automatically and a song starts playing.
Selecting the Band
Push the Control knob towards up to change the
band in the order of FM1 ➜ FM2 ➜ FM3.
Push the Control knob towards down to change
the band to AM.
Playing USB device
Connect a USB device or iPod to the USB
terminal.
When connected, the source is switched
automatically and a song starts playing.
Selecting a Station
Push the Control knob leftward and rightward to
select the station you want to listen to.
Selecting an Audio file folder
Push the Control knob towards up or down to
select a folder.
⁄
Selecting a Song
Traffic information
Push the Control knob towards right or left to
select a song (track or file).
Press the [ ] button for at least 1 second to
turn on or off the traffic information function
alternately.
If traffic bulletin starts when the function is ON,
“Traffic INFO” is displayed and traffic information
is received.
Fast Forwards or Fast Backwards the music
Push and hold the Control knob towards right or
left to fast-forward or fast-backward the audio file
containing songs (tracks or files).
Pause and play
Press the [
] button to pause or resume
playing a song (track or file).
Removing Disc and USB device
Press the [0] button to eject a disc.
Keeping the button pressed for at least 2 seconds
enters the USB Remove mode (“USB REMOVE” is
displayed) and the USB device can be removed
safely.
⁄
• CA-U1EX (optional accessory) is
recommended to connect a USB
device.
CA-U1EX
• KCA-iP101 (optional accessory) is recommended to connect
an iPod.
English
|
5
General opreration
Function of KDC-5047U/ KMR-440U
Muting the audio upon reception of
phone call
Removing the Faceplate
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
The audio system automatically mutes when a call
comes in.
Detaching the Faceplate
Press the Release button.
When a call comes in
“CALL” is displayed.
The audio system pauses.
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
comes back ON.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
comes back ON.
Reattaching the Faceplate
Refer to the following diagram when
reattaching the faceplate.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (Quick
Start Guide).
¤
• Remove the faceplate at once after pressing the Release
button; otherwise it can fall down due to vibration.
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
• Keep the faceplate in its faceplate case while detached.
• Do not place the faceplate (and the faceplate case) in areas
exposed to direct sunlight, excessive heat or humidity. Also
avoid places with too much dust or the possibility of water
splashing.
|
6
KDC-BT50U/ KDC-5047U/ KMR-440U
Audio Adjustments
• About Supreme
Audio Control
Technology to extrapolate and supplement with proprietary
algorithm, the high-frequency range that is cut off when
encoding at low bit rate (less than 128Kbps, Sampling
frequency is 44.1kHz).
Supplementing is optimized by compression format (AAC,
MP3 or WMA) and processed according to bit rate.
The effect is negligible with music that is encoded at high
bit rate, variable bit rate or has minimal high frequency
range.
You can adjust following Audio Control items;
Display
Audio item
Range
“SubWoofer”
“Bass Boost”
“System Q”
Subwoofer output OFF/ON
Bass Boost
Preset Equalizer
curve
Level1/Level2/OFF
“Rock”/“Pops”/“Easy”/
“Top40”/“Jazz”/ ”Game”/
“Natural”/“User”‡
“Bass Adjust”
• About Dual Zone System
“Bass Center FRQ” Bass Center
40/50/60/70/80/100/
120/150 (Hz)
–8 — +8 (dB)
1.00/1.25/1.50/2.00
OFF/ON
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
- When “2Zone” is set to “ON”, the main source sound and
AUX input sound are output to the front speakers and rear
speakers separately.
Frequency
Bass level
“Bass Level”
“Bass Q Factor” Bass Q Factor
“Bass EXT”
Bass Extend
- Set up the channel of sub source by “2Zone”.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by Control knob.
- Adjust the volume of Rear channel by “2Zone Rear
Volume”.
- The Audio Control has no effect on sub source.
- When Bluetooth audio source is selected, set “2Zone F/R
Select” to “Rear”. “2Zone” cannot be turned “ON” when this
is set to “Front”. While “2Zone” is turned “ON”, “2Zone F/R
Select” function is disabled.
“Middle Adjust”
“Middle Center
FRQ”
“Middle Level”
Middle Center
Frequency
Middle level
0.5/1.0/1.5/2.0 (kHz)
–8 — +8 (dB)
1.00/2.00
“Middle Q Factor” Middle Q Factor
“Treble Adjust”
“Treble Center FRQ” Treble Center
Frequency
“Treble Level”
“Balance”
“Fader”
“2Zone Rear Volume” Rear volume during 0 — 35
Dual zone
“SubWoofer Level”
“Detailed Settings”
“HPF Front”
10.0/12.5/15.0/17.5 kHz
Treble level
Balance
Fader
–8 — +8 (dB)
Left 15 — Right 15
Rear 15 — Front 15
1 Select the source to adjust
Press the [SRC] button.
For how to select source item, refer to <Power and
Subwoofer level
–15 — +15 (dB)
2 Enter Audio Control mode
KDC-5047U KMR-440U
Front High Pass
Filter
Rear High Pass Filter Through/40/60/80/100/
120/150/180/220 (Hz)
Through/40/60/80/100/
120/150/180/220 (Hz)
Press the [AUDIO] button.
KDC-BT50U
“HPF Rear”
1) Press the [FNC] button.
2) Turn the Control knob to select “Audio
“LPF SubWoofer” Low Pass Filter
50/60/80/100/120/
Through (Hz)
“Subwoofer Phase” Subwoofer Phase Reverse (180°)/
Normal (0°)
3 Select the Audio item to adjust
Turn the Control knob to select the audio item
for adjustment and then press the [ENTER]
button.
“2Zone”
Dual Zone System ON/OFF
“2Zone F/R Select” Dual Zone output Rear/Front
channel
“Supreme”
Supreme setting ON/OFF
Press the [
item.
] button to return to the previous
“Audio Preset”
Audio Preset
Recall/Memory
memoy†
“Volume Offset
ADJ”
Volume offset
–8 — 0 (dB)
(AUX: -8 — +8)
4 Adjust the Audio item
Turn the Control knob.
5 Determine the setting value
Press the [ENTER] button.
The previous item is displayed.
⁄
•
‡“User”: The customized Bass, Middle, and Treble levels are
effective.
• You can set Bass, Middle, and Treble for each source.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
English
|
7
Audio Adjustments
Audio Preset Memory
Audio Preset Recall
Registering the value setup by Audio Control.
Recalling the sound setup registered by <Audio
1 Setup Audio Control
1 Select the source
Press the [SRC] button.
For how to select source item, refer to <Power and
2 Enter Audio Control mode
KDC-5047U KMR-440U
Press the [AUDIO] button.
KDC-BT50U
2 Enter Audio Control mode
KDC-5047U KMR-440U
1) Press the [FNC] button.
2) Turn the Control knob to select “Audio
Press the [AUDIO] button.
KDC-BT50U
1) Press the [FNC] button.
2) Turn the Control knob to select “Audio
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” ➜“Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” ➜“Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
4 Select the Audio Preset Memory
Turn the Control knob to select “Memory”, and
then press the [ENTER] button.
4 Select the Audio Preset Recall
Turn the Control knob to select “Recall”, and
then press the [ENTER] button.
5 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
“Memory Completed” is displayed.
5 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
“Recall Completed” is displayed.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
⁄
6 Exit Audio Control mode
• To use this function, this unit must be powered for more
than one hour.
Press the [
] button for at least 1 second.
• Register 1 pair of Audio Preset Memory. You cannot register
by the source.
• When you press the Reset, all the sources will be the setting
value which is registered.
• The following items can be registered.
“Bass Center FRQ”, “Bass Level”, “Bass Q Factor”, “Bass EXT”,
“Middle Center FRQ”, “Middle Level”, “Middle Q Factor”,
“Treble Center FRQ”, “Treble Level”, “SubWoofer Level”, “HPF
Front”, “HPF Rear”, “LPF SubWoofer”, “Subwoofer Phase”
|
8
KDC-BT50U/ KDC-5047U/ KMR-440U
Music disc/Audio file Operation
Function of Audio file/ Internal CD source
Function of iPod source
Music Search
Music Search for iPod
Selecting the music you want to listen to from the
device or media being played now.
Searching for the song (in iPod) you want to play.
1 Enter Music Search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
1 Enter Music Search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Search for music
Operation type
2 Search for music
Operation
Movement between items Turn the Control knob.
Audio file
Selection of item
Press the [ENTER].
Operation type
Movement between
folders/files
Operation
Turn the Control knob.
Return to previous item
Return to Top menu
Press the [ ] button.
Push the Control knob towards up for at
least 1 second.
Selection of folder/flie Press the [ENTER].
Return to previous folder Press the [ ] button.
Cancelling the Music Search mode
Press the [ ] button for at least 1 second.
Return to root folder
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button for at least 1 second.
mode
⁄
• If no characters included in a song name can be displayed,
the browse item name and digits are displayed.
¡ indicator: Audio file
] indicator: Folder with a folder or file in the lower
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
layer
Genres
Composers
^ indicator: Folder without a folder or file in the
lower layer
CD source
Operation type
Operation
Movement between track Turn the Control knob.
Selection of track
Press the [ENTER].
Return to first track
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button.
mode
English
|
9
Music disc/Audio file Operation
Function of iPod source
Function of iPod source/ Music Editor media
Alphabet Search
Skip Search
You can select an alphabetic character from the
list in the browse item (artist, album, etc.) currently
selected.
The number of songs to be skipped is determined
by the ratio of the total number of songs in the list
which is selected.
1 Enter Music Search mode
Press the [ ] button.
1 Enter Music Search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
“MUSICSEARCH” is displayed.
2 Select browse item
2 Enter Search select mode
Turn the Control knob to select browse item,
and then press the [ENTER] button.
Press the [ ] button.
3 Select Skip Search mode
Turn the Control knob to select “Skip Search”,
and then press the [ENTER] button.
3 Enter Search select mode
Press the [ ] button.
4 Select Alphabet Search mode
Turn the Control knob to select “Alphabet
Search”, and then press the [ENTER] button.
4 Search for music
Operation type
Operation
Movement between items Turn the Control knob.
Skip Search
Push the Control knob towards up or
down.
Press the [ENTER].
Press the [ ] button.
5 Select the character to be searched for
Operation type
Operation
Selection of item
Return to previous item
Select the characters
Turn the Control knob.
Move the cursor to the enter Push the Control knob towards up or
character position down.
Cancelling the Music Search mode
Press the [ ] button for at least 1 second.
6 Determine the selected character
Press the [ENTER] button.
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
⁄
• Keep pushing Control knob for 3 seconds or longer skips
songs at 10% regardless of the setting.
Cancelling the Music Search mode
Press the [
] button for at least 1 second.
⁄
• The time of Alphabet search may become long depending
on the number of items (songs) in iPod.
• To search for a character other than A to Z and 1 to 9, enter
“*”.
• If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
|
10 KDC-BT50U/ KDC-5047U/ KMR-440U
Function of iPod source
Function of iPod source
Direct Search
Related Search
Searching for music by selecting a browse item and
an alphabetic character(s).
Browsing for music of the same artist or genre as
the one being played.
1 Enter Music Search mode
Press the [ ] button.
1 Enter Music Search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
“MUSICSEARCH” is displayed.
2 Enter Search select mode
Press the [ ] button.
2 Enter Search select mode
Press the [ ] button.
3 Select Direct Search mode
3 Select Related Search mode
Turn the Control knob to select “Direct Search”,
and then press the [ENTER] button.
Turn the Control knob to select “Related
Search”, and then press the [ENTER] button.
“Related Search” is displayed.
4 Select browse item
Turn the Control knob to select browse item,
and then press the [ENTER] button.
4 Select browsing item
Turn the Control knob and press the [ENTER]
button when the desired browse item is
selected.
Display
Browses item
Playlists
Display
Browses music
Artists
“Search Artist”
“Search Album”
Displays the album of the same artist.
Displays music in the album in which the one
being played is included.
Albums
Songs
“Search Genre”
Displays the artist of the same genre.
“Search Composer” Displays the album including music created by the
same composer.
Podcasts
Genres
5 Search for music
Composers
Operation type
Operation
Movement between items Turn the Control knob.
5 Select the character to be searched for
Turn the Control knob to select character, and
then press the [ENTER] button.
Selection of item
Press the [ENTER] button.
Return to previous item
Push the Control knob towards up.
You can select up to three characters.
Cancelling the Related Search
Press the [ ] button for at least 1 second.
6 Search for music
Turn the Control knob to select ”DONE”, and
then press the [ENTER] button.
A search result list is displayed.
⁄
• Related search cannot be performed while playing a
Podcast.
7 Select the music
Turn the Control knob to select music, and then
press the [ENTER] button.
• When the music being played has no information on
browsing items or no music was found, “Not Found” is
displayed.
Cancelling the Music Search mode
Press the [
] button for at least 1 second.
English
|
11
Music disc/Audio file Operation
Function of iPod source
3 Turn the Control knob to select “One” or “All”,
and then press the [ENTER] button.
Selecting “All” deletes all songs.
My Playlist for iPod
You can register your favorite songs to make a
playlist. You can register up to ten songs in the
playlist.
4 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
“Completed” is displayed.
Registering a song in the playlist
⁄
1 Play the song you want to register
Push the Control knob towards up, down, right,
and left.
2 Register the song
Press the [ENTER] button for at least 2 seconds.
“## (registration number) Stored” is displayed. You
can register up to ten songs.
Function of KDC-5047U/ KMR-440U with disc
changers
Basic Operation of Disc Changer
(Optional)
⁄
• When creating a playlist, you can register the songs stored
in one iPod. If you attempt to register a song by connecting
an unregistered iPod, “My Playlist Delete” is displayed.
Selecting “YES” deletes the playlist.
Selecting CD changer source
Press the [SRC] button.
Select the “CD CH” display.
For how to select source item, refer to <Power and
• The song displayed during music search can be registered
in the same manner. For the music search procedure, refer
• If you attempt to register the eleventh song, “Memory Full”
is displayed and you cannot register the song. To register it,
delete an unnecessary song.
Music search
Push the Control knob towards right or left.
• Do not register Podcasts. Songs may be registered or played
improperly. For example, unintended songs are registered.
Disc Search
Push the Control knob towards up or down.
Playing the playlist
1 Display the playlist
Press the [ENTER] button.
“My Playlist” is displayed.
2 Play a song in the playlist
Turn the Control knob to select the song you
want to play and then press the [ENTER] button.
“LIST” indicator is displayed.
⁄
• To stop playing the song in the playlist, turn the power off.
• If a song does not end with 1 second or longer silence, its
last portion may not be played.
• Songs cannot be played at random during playback of the
songs in playlist.
Deleting a song from the playlist
1 Display the playlist
Press the [ENTER] button.
“My Playlist” is displayed.
2 Turn the Control knob to select the song you
want to delete and then press the [ENTER]
button for at least 2 seconds.
|
12 KDC-BT50U/ KDC-5047U/ KMR-440U
Tuner Operation
Station Preset Memory
Preset Tuning
Putting a station in the memory.
Recalling the stations in the memory.
1 Select the frequency to put in the memory
Push the Control knob towards right or left.
1 Enter Preset Tuning mode
Press the [ ] button.
2 Enter Preset Memory mode
2 Recall the station
Press the [ ] button.
Turn the Control knob to select recall number
(“P1” – “P6”), and then press the [ENTER].
3 Preset the station
Turn the Control knob to select preset number
(“P1” – “P6”), and then press the [ENTER] button
for at least 2 seconds.
Cancelling Preset Tuning
Press the [
] button.
Cancelling the Preset Memory mode
Press the [
] button.
English
|
13
Tuner Operation
PTY (Program Type)
Program Type Preset
Selecting the Program Type below and searching
for a station;
Putting the Program Type in the Preset button
memory and quick recall.
Program Type Display
Program Type Display
Serious Classical “Classics”
Presetting the Program Type
1 Select the Program Type to preset
Speech
Music
News
“Speech”
“Music”
“News”
Other Music
Weather
Finance
“Other M”
“Weather”
“Finance”
2 Enter Program Type Preset mode
Press the [ ] button.
Current Affairs
Information
Sport
“Affairs”
“Info”
“Sport”
Children’s programs “Children”
Social Affairs
Religion
Phone In
“Social”
3 Preset the Program Type
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening
Music
“Educate”
“Drama”
“Culture”
“Science”
“Varied”
“Pop M”
“Rock M”
“Easy M”
“Religion”
“Phone In”
“Travel”
Turn the Control knob to select preset number
(“P1” – “P6”), and then press the [ENTER] button
for at least 1 second.
Travel
Leisure
“Leisure”
“Jazz”
“Country”
“Nation M”
“Oldies”
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Recalling the preset Program Type
1 Enter PTY mode
Press the [ ] button twice.
“Folk M”
“Document”
2 Enter Program Type Preset mode
Press the [ ] button.
Light Classical
“Light M”
• Speech and Music include the Program type shown below.
Music: Black character item.
Speech: White character item.
3 Recall the Program Type
Turn the Control knob to select recall number
(“P1” – “P6”), and then press the [ENTER]
button.
1 Enter PTY mode
Press the [ ] button twice.
2 Select the Program Type
Turn the Control knob.
Changing Language for PTY Function
3 Search for the selected Program Type station
Push the Control knob towards right or left.
Selecting the Program Type display language as
follows;
4 Exit PTY mode
Press the [
] button.
Language
English
French
Display
“English”
“French”
“German”
⁄
• This function cannot be used during a traffic bulletin or AM
reception.
German
• When the selected Program Type is not found, “No PTY” is
displayed. Select another Program Type.
1 Enter PTY mode
Press the [ ] button twice.
2 Enter Changing Language mode
Press the [ENTER] button.
3 Select the language
Turn the Control knob to select language, and
then press the [ENTER].
|
14 KDC-BT50U/ KDC-5047U/ KMR-440U
Favorite Control
Favorite Preset Memory
Favorite Preset Recall
You can register frequently used items such as
broadcast stations, iPod Playlist or Artists, Function
setting items, or Audio control items.
Retrieving an item registered to Favorite.
1 Enter Favorite Preset Recall mode
Press the [FAVORITE] button.
1 Display the item you want to register
2 Select the number to recall in the Favorite
memory
Turn the Control knob.
Registerable items are as follows:
Source
TUNER
Registerable items
Frequency
3 Recall the Favorite Preset
Press the [ENTER] button.
iPod
Browse item such as Playlists/Artists/Albums
Function setting item
Audio control item
Display control item
Telephone number retrieval.
Function setting
Audio control*
Display control*
Hands-free phone
Cancelling the Favorite Preset Recall mode
Press the [
] button.
* Function of KDC-5047U/ KMR-440U
(For the KDC-BT50U, Audio control item and Display control
item are contained in Function setting.)
Deleting Favorite Preset Memory
When selecting registerable items, the “
indicator is lit for 5 seconds.
”
FAV
Deleting an item registered to Favorite.
1 Select Standby
Press the [SRC] button.
Go through step 2 and later by the item which the
” indicator is lit.
“
FAV
Select the “STANDBY” display.
For how to select source item, refer to <Power and
When a setting operation of each item can be
done in the Function setting, the “ ” indicator
goes out and you cannot register to the Favorite.
FAV
2 Enter Function setting mode
2 Enter Favorite Preset Memory mode
Press the [FAVORITE] button for at least 1
second.
Press the [FNC] button.
3 Select Favorite Delete mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
3 Select the number to put in the memory
Turn the Control knob.
4 Put the Favorite Preset in the memory
Press the [ENTER] button.
Cancelling the Favorite Preset Memory mode
4 Select the number you want to delete
Turn the Control knob to select memory
number, and then press the [ENTER] button.
“Favorite Delete” is displayed.
Press the [
] button.
⁄
• Register 6 pairs of Favorite Preset Memory.
“Register your favorite functions” is displayed for numbers
available for preset.
Select “All” if you want to delete all.
5 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
“Completed” is displayed.
• The memory cannot be erased by the Reset button.
• Registering the operation procedure to an existing preset
number overwrites the existing procedure.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
• If the items in the second or lower hierarchy are changed,
the list in iPod will be changed by adding or deleting
songs after the FAVORITE registration. Due to this, the list
registered in this unit will be different from the list in iPod.
The FAVORITE registration should be performed again after
editing the items in iPod.
• To use this function, this unit must be powered for more
than one hour.
English
|
15
Function setting
Configure the functions of this unit using the
following procedure:
Function item
Example:
1 Search for the item to set
Pick up the item to set according to <Function
No. Function name: “Display of each function on
this unit” ➤ “Setting value 1”*, “Setting value 2”...
Provides a functional overview of the function
item. The source that displays this function can be
2 Select the source
Press the [SRC] button.
Switch to the source that displays the item to set
For how to select source item, refer to <Power and
⁄
• The underscored setting value is a factory setting.
3 Enter Function setting mode
Music Play Mode
Press the [FNC] button.
“OFF”
When set to “ON”, allows you to operate iPod with
the control on the iPod.
When set to “ON”, plays the intro of the music in
the disc/folder successively.
When set to “ON”, plays the music in the disc/
folder randomly.
When set to “ON”, all songs in iPod are played at
random.
4 Select the Function item
Turn the Control knob to select the item to set.
5 Enter the selected Function item
Press the [ENTER] button.
Press the [
item.
] button to return to the previous
Repeat steps 4 and 5 until you get to the item to
set.
6 Set the Function item
Turn the Control knob to select a desired
setting value.
7 Determine the setting value
Press the [ENTER] button.
When set to “ON”, plays the music repeatedly.
”OFF”
The previous item is displayed.
8 Exit Function setting mode
Press the [
] button for at least 1 second.
When set to “ON”, plays the music in the disc/
folder repeatedly.
”OFF”
When set to “ON”, plays the music in the disc
changer randomly.
Function of KDC-5047U/ KMR-440U.
|
16 KDC-BT50U/ KDC-5047U/ KMR-440U
Display Control
Display & Illumination Settings
Sets the faceplate illumination color. Refer to
Function of KDC-BT50U/ KDC-5047U.
“OFF”
types
Sets the display pattern.
Display type
Type A
Type B
Display information
Displays 2 lines of text.
Displays a line of text.
Displays the status.
Type C
If this unit is not operated at least 5 seconds with
“ON” selected, the display turns off. During a
setup mode, the display will not turn off even if 5
seconds lapse.
Type D
Displays the clock.
Type E
Displays the spectrum analyzer.
2 types
Sets the Type A, B, D, and E side display to ON/
Sets the Type A and B text display. Refer to
Function of KDC-BT50U/ KDC-5047U.
“Manual1”, “Manual2”, “OFF”
Dims the display part in conjunction with the light
switch of the vehicle.
Setting to “Auto” scrolls the displayed text
automatically.
Sets the Type E spectrum analyzer display. Refer to
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
: Signal strength of cell-phone.
Function of KDC-BT50U/ KCA-BT200 (Optional
Accessory).
Clock & Date Settings
Sets the clock.
1. Turn the Control knob to adjust the hour, and
then press the [ENTER] button.
2. Turn the Control knob to adjust the minute, and
then press the [ENTER] button.
“Auto”, “Manual1”, “Manual2”, “OFF”
Reduces the key Illumination brightness.
Auto: Dims the illumination in conjunction with
the Light switch of the vehicle.
Synchronizing the Time is set to “OFF”.
➤ “ON”, “OFF”
Synchronizing the RDS station time data and this
unit’s clock.
Sets the date. Refer to <Adjusting the Date>
Manual1: Dims the illumination constantly.
Manual2: Dims the illumination darker than
Manual1.
OFF: Does not dim the illumination.
”OFF”
Sets whether the key illumination color is
changed in conjunction with the key operation.
Sets the date display mode. Refer to <Adjusting
Sets whether the key illumination color is
changed in conjunction with the sound volume.
English
|
17
Function setting
Tuner Settings
iPod Settings
Only stations whose reception is good are
searched in auto seek tuning.
”Manual”
“10%”
Sets the ratio of skip performed with <Skip
Deletes the songs registered in My Playlist.
Turn the Control knob to select “YES” and then
press the [ENTER] button to delete My Playlist.
Selects the tuning mode of the radio.
Tuning mode
Display Operation
Auto seek
“Auto1” Automatic search for a station.
Preset station seek “Auto2” Search in order of the stations in
the Preset memory.
AUX Settings
Manual
“Manual” Normal manual tuning control.
“PORTABLE”, “GAME”, “VIDEO”, “TV”
Memorizes six stations with good reception
automatically.
Sets the display when switched to AUX source.
Turn the Control knob to select “YES” and then
press the [ENTER] button to start the auto
memory operation.
Audio Settings
Sets the sound quality and speaker system. Refer
You can reduce the noise when stereo broadcasts
are received as monaural.
Function of the KDC-BT50U.
Automatically receives news bulletin when it
starts. Set the time during which interrupt is to be
disabled after start of another news bulletin.
Changing “00MIN” to “90MIN” turns this function
ON.
Initial Settings
Sets the source selection method.
Setting the operation check sound (beep sound)
ON/OFF.
If news bulletin starts when this function is
ON, “NEWS” is displayed and news is received.
If “20MIN” is has been set, reception of another
news bulletin will not start for 20 minutes.
The news bulletin volume is the same level that
was set for Traffic Information.
“OFF”
When this is set to ON, the following character
strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist name/
Album name/ KCA-BT200 (optional accessory)
“German”, “Italian”, “Russian”
When the reception is poor, automatically
alternate to another frequency broadcasting the
same program in the same RDS network with
better reception.
Changes the display language of items in
Function setting.
Sets whether to switch to the station only in the
specific region using the “AF SET” control.
When traffic information station reception is poor,
automatically searches for a station that can be
received better.
“20MIN”, “40MIN”, “60MIN”
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
OFF: Power OFF Timer function is OFF.
20MIN: Turns the power OFF after 20 minutes.
(Factory setting)
40MIN: Turns the power OFF after 40 minutes.
|
18 KDC-BT50U/ KDC-5047U/ KMR-440U
60MIN: Turns the power OFF after 60 minutes.
Function of the KDC-BT50U/ KDC-5047U.
Sets whether to display AUX during source
selection.
Function of KDC-BT50U/ KCA-BT200 (Optional
Accessory)
Bluetooth Settings
Select a cell-phone subject to hands-free
connection. Refer to <Selecting the Bluetooth
Select the Bluetooth audio player to be
connected. Refer to <Selecting the Bluetooth
Download a short message. Refer to
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CDs may be unplayable even when set to
“2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
Display the received short message. Refer to
Function of KCA-BT200 (Optional Accessory).
Registers voice for voice recognition. Refer to
Function of KCA-BT200 (Optional Accessory).
”All”
Deletes Favorite Preset Memory.
Refer to <Deleting Favorite Preset Memory>
“OFF”
Selecting “OFF” turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
”5/4inch”, ”6x9/6inch”, ”O.E.M”
Registers voice to select the Phone number
category in Phonebook. Refer to <Setting a Voice
Function of KCA-BT200 (Optional Accessory).
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
Register a Bluetooth device (pairing). Refer to
Allow registration of a special device that cannot
be registered normally. Refer to <Registering
Speaker type
OFF
Display
“OFF”
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
“5/4inch”
“6x9/6inch”
“O.E.M”
”CD”
Cancel registration of the Bluetooth device. Refer
Upgrades the firmware.
Selecting “YES” and then pressing [ENTER] button
starts upgrading the firmware.
For how to update the firmware, access our web
site.
Specify the PIN code required when registering
this unit using the Bluetooth device. Refer to
Demo Mode Settings
Specifies whether to enable demonstration.
English
|
19
Function setting
58 Setting the Time Interval for Automatic
– “99SEC”
Function list
Function items that appear when any
source is selected
This function automatically answers (responds
to) a call after lapse of the preset time interval for
automatic answer.
“OFF” : Does not answer the phone call
automatically.
Function item list
No.
“Settings”
“Clock & Date”
“Clock Adjust”
“Time Synchronized”
“Date Adjust”
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call
after lapse of 1 – 99 seconds.
“Date Mode”
“Color SEL”
“DISP & ILLUMI”
“DISP OFF Mode”
“Display Dimmer”
“Text Scroll”
“BT DVC Status”
“ILLUMI Dimmer”
“ILLUMI Effect”
“ILLUMI Music SYNC”
”All”
You can specify output speakers for hands-free
voice communication and Bluetooth audio sound.
“Front” : Outputs sound from the front speakers.
“All” : Outputs sound from the front and rear
speakers.
“Display Control” (“DISP SELECT”)
“DEMO Mode”
“DISP Side Select”
“DISP Text Select”
“DISP GRPHC Select”
You can output a beep from the speaker when a
call comes in.
“ON” : Beep is heard.
Function items that appear during
standby
“OFF” : Beep is canceled.
Displays the firmware version and update the
firmware. Refer to <Displaying the Firmware
Adjusts the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to “+” increases the voice volume.
Function of the KDC-BT50U.
Reduces the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to “+” increases the
noise reduction.
Function item list
“Initial Settings” “SRC Select”
“Key Beep”
No.
“Russian”
“Function Language”
“Power OFF Wait”
“Built-in AUX”
“CD Read”
“Favorite Delete”
“Built-in AMP”
“Speaker Select”
“F/W Update #.##”
Function of the KDC-BT50U.
– “+2”
Sets the echo cancellation level.
Function of the KDC-BT50U.
Determines whether the built-in or external
microphone is to be used when the receiver
incorporates a microphone.
Builtin: Use the built-in microphone.
External: Use the external microphone.
Function of the KDC-BT50U.
|
20 KDC-BT50U/ KDC-5047U/ KMR-440U
Function items that appear during
playback of a CD, audio file, or iPod
Function items that appear in the BT
mode
Function item list
“Audio Control”
No.
Function item list
No.
“Settings”
“Phone Selection”
“Audio Selection”
“SMS Download”
“SMS Inbox”
“Play Mode”
“Hands Mode”(iPod)
“Track Scan”(CD)/“File Scan”(Audio file)
“Disc Random”(CD)/“Folder Random”(Audio
file/ iPod)
“All Random”(iPod)
“Track Repeat”(CD)/“File Repeat”(Audio
file/ iPod)
“Voice Tag”
“PB Name Edit”
“PN Type Edit”
“Device Regist.”
“SPCL DVC Select”
“Device Delete”
“PIN Code Edit”
“Auto Answer”
“Bluetooth HF/
Audio”
“Call Beep”
“BT F/W Update”
“MIC Gain”
“NR Level”
“Echo Cancel”
“MIC Select”
“Detailed Settings”
“Disc Repeat”(CD changer)/“Folder Repeat”
(Audio file)
“MGZN Random”(Disc changer)
“Skip Search”(iPod/ Music Editor media)
“My Playlist Delete”(iPod)
“News Interrupt”
“Settings”
“RDS Settings”
“AF”
“RDS Regional”
“Auto TP Seek”
Function items that appear when the
tuner source is selected
Function item list
“Audio Control”
No.
⁄
• The Bluetooth Function setting items can be set while in
the Bluetooth mode without selecting the Function setting
mode.
“Settings”
“Local Seek”(FM)
“Seek Mode”
“Auto Memory”
“MONO”(FM)
“News Interrupt”
“AF”(FM)
“RDS Regional”(FM)
“Auto TP Seek”(FM)
1. Press the [
] button ( KDC-BT50U )/ [FNC] button for
at least 1 second ( KDC-5047U KMR-440U ) to enter the
Bluetooth mode.
2. Turn the Control knob to select “BT Setting”, and then
press the [ENTER] button.
3. Turn the Control knob to select desired item, and then
press the [ENTER] button.
4. Turn the Control knob to select value, and then press the
[ENTER] button.
Function items that appear when the
AUX source is selected
Function item list
“Audio Control”
No.
“Settings”
“RDS Settings”
“Name Set”
“News Interrupt”
“AF”
“RDS Regional”
“Auto TP Seek”
English
|
21
Display Settings
Selecting Display Type
Selecting Text Display
Shown below are examples of display types.
Changes displayed information on each of the
following sources:
Display
Type A
Type B
Type C
Type D
Type E
Display Type
Displays 2 lines of text.
Displays a line of text.
Displays the status (ON/OFF indicator for each function).
Displays the clock.
In Tuner source
Information
Display
Frequency & Program Service name (FM)
Title & Artist name* (FM)
Station name* (FM)
“Frequency/PS”
“Title/Artist”
“Station Name”
“Radio Text Plus”
“Radio Text”
“Frequency”
“Speana/Clock”
“Date”
Displays the spectrum analyzer.
Radio text plus* (FM)
1 Enter Display control mode
KDC-5047U KMR-440U
Radio text (FM)
*
Frequency (MW, LW)
Spectrum analyzer & Clock
Date
Press the [DISP] button.
KDC-BT50U
1) Press the [FNC] button.
2) Turn the Control knob to select “Display
Displays the status (Type A display only)
Blank
“Indicator”
“Blank”
*Information of Radio text plus is displayed.
2 Select Display type
Turn the Control knob to select Display type,
and then press the [ENTER] button.
In CD & External disc source
Information
Disc title
Display
“Disc Title”
“Track Title”
“P-Time”
“Speana/Clock”
“Date”
Track title
Play time
Spectrum analyzer & Clock
Date
3 Select Display information item
Turn the Control knob to select Display
information item, and then press the [ENTER]
button.
Displays the status (Type A display only)
Blank
“Indicator”
“Blank”
The following display information items can be set:
• Side display selection (When selecting Display
type A, B, D, or E.)
• Text display selection (When selecting Display
type A or B.)
• Graphic selection (When selecting Display type
E.)
In Audio file/ iPod source
Information
Title & Artist name
Album & Artist name
Folder name
Display
“Title/Artist”
“Album/Artist”
“Folder Name”
“File Name”
“P-Time”
“Speana/Clock”
“Date”
“Indicator”
“Blank”
File name
Play time
Spectrum analyzer & Clock
Date
Displays the status (Type A display only)
Blank
In Bluetooth Audio “BT Audio” (KDC-BT50U)/
“BT Audio EXT” (KCA-BT200; Optional
accessory) source
4 Exit Function setting mode
Press the [
] button for at least 1 second.
Information
Display
Source name
“Source Name”
“Title/Artist”
“Album/Artist”
“Speana/Clock”
“Date”
Title & Artist name (KDC-BT50U only)
Album & Artist name (KDC-BT50U only)
Spectrum analyzer & Clock
Date
Displays the status (Type A display only)
Blank
“Indicator”
“Blank”
|
22 KDC-BT50U/ KDC-5047U/ KMR-440U
In Standby/ Auxiliary input source
Function of KDC-BT50U/ KDC-5047U
Information
Source name
Spectrum analyzer & Clock (AUX only)
Clock (Standby only)
Display
Illumination Color Selection
“Source Name”
“Speana/Clock”
“Clock”
“Date”
“Indicator”
“Blank”
Selecting the Illumination Color of the panel.
1 Enter Function setting mode
Press the [FNC] button.
Date
Displays the status (Type A display only)
Blank
2 Select Color select mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
1 Enter Display control mode
KDC-5047U KMR-440U
Press the [DISP] button.
KDC-BT50U
1) Press the [FNC] button.
2) Turn the Control knob to select “Display
3 Select the part where you want to set the
Illumination Color
Part
All
Display
“All”
2 Select the Display type
Turn the Control knob to select Display type A
or B, and then press the [ENTER] button.
Button
“Key”
Control knob
USB/ Auxiliary Terminal
“Rotary”
“USB & AUX”
3 Select Text display selection mode
Turn the Control knob to select “DISP Text
Turn the Control knob to select part, and then
press the [ENTER] button.
4 Select the text display part (Display type A
only)
Push the Control knob towards up or down.
The selected text display part blinks.
4 Select the Illumination Color
Turn the Control knob to select color, and then
press the [ENTER] button.
Select the color from “Variable Scan”/ “Color1” —
“Color 24”.
5 Select the text
Turn the Control knob.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
⁄
• If the selected display item does not have any information,
alternative information is displayed.
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder name” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod By Hand Mode” is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Information
Music title
Folder name
File name
Display
“TITLE***”
“FLD***”
“FILE***”
English
|
23
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
Before Use
• For details on the Bluetooth cell-phone with the
hands-free function, see <About the Cell-Phone>
• You need to register your cell-phone before using
it with this unit. For more details, see <Registering
4 Search for the Name
Press the [ENTER] button.
5 Select the phone number
Turn the Control knob.
Pushing the Control knob towards right or left sorts
the Phone Book by name
6 Make a call
• If you have registered two or more cell-phones,
you need to select one of them. For more details,
• To use the Phone Book, it must be downloaded to
this unit in advance. For details, see <Downloading
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ENTER] button.
⁄
• The display changes in name, telephone number, and time-
stamp whenever pressing the [ENTER] button. ( KDC-BT50U )
• During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
Receiving a call
Answering a Phone Call
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ENTER] button.
Dialing a number
⁄
1 Enter Bluetooth mode
KDC-BT50U
• The following operations disconnect the line:
- Insering a CD.
Press the [ ] button.
KDC-5047U KMR-440U
- Connecting a USB device.
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
Rejecting an Incoming Call
2 Select the Number dial mode
Turn the Control knob to select “Number Dial”,
and then press the [ENTER] button.
KDC-BT50U
Press the [
KDC-5047U KMR-440U
] button.
Press the [SRC] button.
3 Enter a phone number
Turn the Control knob to select number, and
then Push the Control knob towards right.
Calling a number in the Phone Book
4 Make a call
1 Enter Bluetooth mode
KDC-BT50U
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ENTER] button.
Press the [ ] button.
KDC-5047U KMR-440U
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
To erase the entered phone number digit by
digit:
Push the Control knob towards left.
2 Select the Name search mode
Turn the Control knob to select “Name Search”,
and then press the [ENTER] button.
⁄
• You can input a maximum of 32 digits.
3 Enter the initial of name
Operation type
Operation
Select the characters.
Move the character page.
Turn the Control knob.
Push the Control knob towards up or
down.
|
24 KDC-BT50U/ KDC-5047U/ KMR-440U
KDC-5047U KMR-440U
Calling a number in the call log
Press the [ENTER] button.
1 Enter Bluetooth mode
KDC-BT50U
⁄
• You need to register the preset dial number. Refer to
Press the [ ] button.
KDC-5047U KMR-440U
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
Registering to the Preset Dial Number
List
2 Select the call log mode
Turn the Control knob to select “Incoming
Calls”, “Outgoing Calls”, or “Missed Calls”, and
then press the [ENTER] button.
“Incoming Calls”: Incoming calls
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dialing a number/ Calling a number in the call log/
Calling a number in the Phone Book
“Outgoing Calls”: Outgoing calls
“Missed Calls”: Missed calls
3 Select a name or phone number
Turn the Control knob.
2 Enter Preset Memory mode
Press the [ ] button.
4 Make a call
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“P1” – “P6”), and then press the
[ENTER] button for at least 2 second.
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ENTER] button.
Cancelling the Preset Memory mode
⁄
Press the [
] button.
• The display changes in name, telephone number, and time-
stamp whenever pressing the [ENTER] button. ( KDC-BT50U )
• The outgoing call list, the incoming call list, and the missed
call list, are the lists of calls originated from and received
at this unit. They are not the ones stored in the cell-phone
memory.
During a call
Disconnecting a Call
Press the [SRC] button.
Switching to the Private Mode
Push the Control knob towards right or left.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
Speed dialing (Preset dial)
1 Enter Bluetooth mode
KDC-BT50U
⁄
Press the [ ] button.
KDC-5047U KMR-440U
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection. If
this happens, the source cannot be switched back to the
hands-free talk mode by operating this unit. Operate your
cell-phone to return to the hands-free talk mode.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Select the number you want to recall from the
memory
Turn the Control knob to select recall number
(“P1” – “P6”), and then press the [ENTER]
button.
Adjusting the Voice Volume during a Call
Turn the Control knob.
3 Make a call
KDC-BT50U
Press the [ ] button.
English
|
25
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
Function of KCA-BT200 (Optional Accessory)
Call waiting
Making a voice dialing call
Answering Another Incoming Call with the
Current Call Suspended
1 Enter Bluetooth mode
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
2 Enter voice recognize mode
1) Press the [FNC] button for at least 1 second.
2) Turn the Control knob to select “Answer”, and
then press the [ENTER] button.
Press the [AUDIO] button for at least 1 second.
3 Have the unit recognize your spoken name
Press the [ENTER] button. If you hear a beep,
speak a registered name within 2 seconds.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
4 Have the unit recognize the spoken category
When you hear a beep, speak the category
within 2 seconds.
The recognized phone number (name) is displayed.
When you want to change the displayed phone
number (name), press the [DISP] button.
Continuing the Current Call
KDC-BT50U
Press the [
] button.
KDC-5047U KMR-440U
1) Press the [ENTER] button.
2) Turn the Control knob to select “Reject”, and
then press the [ENTER] button.
5 Make a call
Press the [ENTER] button.
⁄
Answering the Waiting Call after Terminating
the Current Call
• If your voice cannot be recognized, a message is displayed.
Pressing the [ENTER] button allows you to retry voice input.
• Both the name and category requires registration of a voice
tag. Refer to <Setting a Voice Command for Category>
Press the [SRC] button.
Switching between the Current Call and Waiting
Call
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ENTER] button.
Each pressing of this knob switches the calling
party.
Displays of phone number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
“General”/“
Information
General
Clearing the Disconnection Message
”
KDC-BT50U
“Home”/“
“Office”/“
“Mobile”/“
“Other”/“
”
Home
Office
Mobile
Other
Press the [ ] button.
KDC-5047U KMR-440U
”
Press the [FNC] button for at least 1 second.
”
”
“HF Disconnect” disappears.
|
26 KDC-BT50U/ KDC-5047U/ KMR-440U
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Bluetooth Audio Operation
Before Use
• For details on the Bluetooth Audio player which
can be connected, see <About the Bluetooth Audio
• You need to register your Bluetooth Audio player
before using it with this unit. For more details, see
• You need to select the Bluetooth audio player you
wish to connect. Refer to <Selecting the Bluetooth
Basic Operation
Selecting Bluetooth Audio source
Press the [SRC] button.
Select the “BT AUDIO” ( KDC-BT50U )/ “BT AUDIO
EXT” ( KDC-5047U KMR-440U ) display.
For how to select source item, refer to <Power and
Pause and play
Press the [
] button.
Music Search
Push the Control knob towards right or left.
⁄
• All or some of the operations above cannot be performed if
the Bluetooth audio player is not ready for remote control.
• Switching between Bluetooth audio sources does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
• When “2Zone” is set to “ON” and “2Zone F/R Select” is set to
cannot be selected.
English
|
27
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Bluetooth Setup
KDC-5047U KMR-440U
Registering Bluetooth device
Input the PIN code (steps 5 and 6).
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to five Bluetooth devices to this unit.
5 Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
When registering from Bluetooth devices
1 Turn on the this unit.
2 Start registering a unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD
BT CD/R-4P1” or “KCA-BT200” from the list of
connected units.
6 Transmit the PIN code
Press the [ENTER] button.
If “Pairing Success” is displayed, registration is
complete.
7 Return to the device list
Press the [ENTER] button.
3 Enter a PIN code
Input the PIN code registered as mentioned in
Check that registration is complete on the
Bluetooth device.
8 Exit Bluetooth mode
Press the [SRC] button.
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
4 By operating the Bluetooth device, start hands-
free connection.
• If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
When registering from this unit
• If the error message appears even though the PIN code is
1 Enter Bluetooth mode
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
2 Enter Function setting mode
Press the [FNC] button.
3 Select Bluetooth device registration mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
Search for the Bluetooth device.
1 Enter Bluetooth mode
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
When search is completed, “Finished” is displayed.
3 Select Special device registration mode
The item can be selected and determined as
follows.
4 Select the Bluetooth device
Turn the Control knob to select desired
Bluetooth device, and then press the [ENTER]
button.
KDC-BT50U
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
When “Paring Success” is displayed, PIN code input
(steps 5 and 6) is not required. When “Pin Code NG”
is displayed, press the [ENTER] button. Then enter
the PIN code (steps 5 and 6).
4 Select a device name
Turn the Control knob to select desired device
|
28 KDC-BT50U/ KDC-5047U/ KMR-440U
name, and then press the [ENTER] button.
If “Completed” is displayed, registration is
completed.
Downloading the Phone Book
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
Bluetooth device> (page 28) and complete the
registration (pairing).
Downloading automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
Cancelling Bluetooth mode
Press the [FNC] button.
⁄
• If the device name is not in the list, select “Other Phones”.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after
“Completed” is displayed, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
Registering PIN Code
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
Downloading from the cell-phone manually
1 Operate the cell-phone to end the hands-free
connection.
1 Enter Bluetooth mode
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
2 Operate the cell-phone to send the phone
book data to this unit
By operating the cell-phone, download the phone
book data to this unit.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
• During downloading:
“Downloading” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
• After completion of downloading:
“Completed” is displayed.
3 Select PIN code edit mode
The item can be selected and determined as
follows.
3 Operate the cell-phone to start the hand-sfree
connection.
Clearing the downloading completion message
Press any button.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
⁄
4 Input the PIN code
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
Operation type
Operation
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type of
characters.)
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
5 Register a PIN code
Press the [ENTER] button.
If “Completed” is displayed, registration is complete.
• To cancel downloading of the phone book data, operate
the cell-phone.
6 Exit Bluetooth mode
Press the [SRC] button.
⁄
• By default, “0000” is specified.
• A PIN code can be specified with up to eight digits.
English
|
29
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Bluetooth Setup
Selecting the Bluetooth device You
Wish to Connect
Deleting a Registered Bluetooth
device
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
You can delete a registered Bluetooth device.
1 Enter Bluetooth mode
KDC-BT50U
1 Enter Bluetooth mode
KDC-BT50U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [ ] button.
KDC-5047U KMR-440U
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
2 Enter Function setting mode
3 Select Bluetooth device deletion mode
The item can be selected and determined as
follows.
Press the [FNC] button.
3 Select Bluetooth device selection mode
The item can be selected and determined as
follows.
audio player)
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
Device name is displayed.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
“(name)” is displayed.
4 Delete the selected Bluetooth device
Turn the Control knob to select desired device
name, and then press the [ENTER] button.
4 Select the Bluetooth device
Turn the Control knob.
5 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
“Completed” is displayed.
5 Set up the Bluetooth device
Press the [ENTER] button.
6 Exit Bluetooth mode
Press the [SRC] button.
‘✱(name)’ or ‘-(name)’ is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
⁄
• When a registered cell-phone is deleted, its Phone Book,
log, SMS, and voice tag are also deleted.
6 Exit Bluetooth mode
Press the [SRC] button.
⁄
• If a cell-phone is already selected, deselect it, and then
select a different one.
• If you cannot select a device using the audio player,
connect the device with the audio player.
|
30 KDC-BT50U/ KDC-5047U/ KMR-440U
Displaying the Firmware Version
5 Select a mode
Turn the Control knob.
Display the version of the firmware of this unit.
Display
Operation
Register a voice tag.
Play a voice tag.
1 Enter Bluetooth mode
KDC-BT50U
“Register”
“Check”*
“Delete”*
Press the [ ] button.
KDC-5047U KMR-440U
Delete a voice tag.
*Displayed only when a name for which a voice tag has
been registered is selected.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
Selecting “Register” (Regist)
2 Enter Function setting mode
Press the [FNC] button.
6 Register a voice tag (first)
Press the [ENTER] button. When you hear a
beep, speak the voice tag within 2 seconds.
3 Select Bluetooth Firmware update mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
The firmware version appears.
7 Confirm the voice tag (second)
Press the [ENTER] button. When you hear a
beep, speak the same voice tag again within 2
seconds.
“Completed” is displayed.
8 Exit Function setting mode
Press the [
Return to step 2. You can register another voice tag
continuously.
] button for at least 1 second.
4 Exit Bluetooth mode
Press the [SRC] button.
⁄
⁄
• For how to update the firmware, access our web site.
• If your voice cannot be recognized, a message is displayed.
Pressing the [ENTER] button allows you to retry voice input.
Selecting “Check” (Play)
Function of KCA-BT200 (Optional Accessory)
6 Press the [ENTER] button.
Play the registered voice and return to step 2.
Adding a voice dialing command
Add a voice tag to the phonebook for voice dialing.
You can register up to 35 voice tags.
Selecting “Delete” (Delete)
6 Delete a voice tag
Press the [ENTER] button.
1 Enter Bluetooth mode
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
7 Turn the Control knob to select “YES”, and then
press the [ENTER] button.
2 Enter Function setting mode
Press the [FNC] button.
Exit Bluetooth mode
Press the [SRC] button.
3 Select Phonebook name edit mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
4 Search for the name to register
Turn the Control knob to select name, and then
press the [ENTER] button.
If a voice tag has already been registered for a
name, “*” is displayed before the name.
English
|
31
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
Bluetooth Setup
Function of KCA-BT200 (Optional Accessory)
Setting a Voice Command for
Category
Add a voice tag to the phone number category
(type) for voice calling.
1 Enter Bluetooth mode
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
3 Select Phone Number type edit mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
4 Enter Phone Number type edit mode
Press the [ENTER] button.
5 Select the category (type) you wish to set
Turn the Control knob to select desired
category name, and then press the [ENTER]
button.
“General”/ “Home”/ “Office”/ “Mobile”/ “Other”
6 Select a mode
Turn the Control knob.
Display
Operation
“Register”
“Check”*
“Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
*Displayed only when a name for which a voice tag has
been registered is selected.
7 Register the category (type) by performing
steps 6 to 7 in <Adding a voice dialing
8 Exit Bluetooth mode
Press the [SRC] button.
⁄
• Set the voice tag for all the 5 categories. If the voice tag is
not registered for all the categories, the Phonebook may
not be recalled by voice command.
|
32 KDC-BT50U/ KDC-5047U/ KMR-440U
Function of KDC-BT50U/ KCA-BT200 (Optional Accessory)
SMS (Short Message Service)
Displaying the SMS
Downloading the SMS
The SMS received by the cell-phone is displayed on
the receiver.
Download the short message (SMS) received by the
cell-phone so that it can be read on this unit.
A newly received message is displayed.
1 Enter Bluetooth mode
KDC-BT50U
¤
• To prevent car accidents, the driver should not read the
Press the [ ] button.
KDC-5047U KMR-440U
SMS while driving.
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
2 Enter Function setting mode
Press the [FNC] button.
Displaying the SMS
3 Select SMS download mode
The item can be selected and determined as
follows.
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
1 Enter SMS Inbox mode
KDC-BT50U
Press the [
] button for at least 1 second.
KDC-5047U KMR-440U
1) Press the [FNC] button for at least 1 second.
2) Press the [FNC] button.
3) The item can be selected and determined as
follows.
To select the item, turn the Control knob.
To determine the item, press the [ENTER]
button.
4 Start downloading
Press the [ENTER] button.
“SMS Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
5 Exit Bluetooth mode
Press the [SRC] button.
2 Select a message
Turn the Control knob.
Each press of the [ENTER] button ( KDC-BT50U )/
[DISP] button ( KDC-5047U KMR-440U ) switches
between displaying the telephone number or
name and message reception date.
⁄
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required. If
the cell-phone does not support SMS function, the SMS
download item in Function Control mode is not displayed.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The up to 75 already-read and unread short messages
respectively can be downloaded.
3 Display the text
Press the [ENTER] button.
Turn the Control knob to scroll through the
message.
Press the [ENTER] button to return to the message
list screen.
4 Exit Bluetooth mode
Press the [SRC] button.
⁄
• The unopened message is displayed at the beginning of the
list. Other messages are displayed in the order of reception.
• The SMS that are received when the cell-phone is not linked
with Bluetooth cannot be displayed. Download the SMS.
• The short message cannot be displayed during
downloading the SMS.
English
|
33
Appendix
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
About Audio file
•
•
•
•
Playable Audio file
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
iPod/iPhone that can be connected to this
unit
Made for
• iPod nano (1st generation) • iPod nano (2nd generation)
• iPod nano (3rd generation) • iPod nano (4th generation)
• iPod nano (5th generation) • iPod with video
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
•
Even if the audio files comply with the standards listed
above, the play may be impossible depending on the
types or conditions of media or device.
• iPod classic
• iPod touch (1st generation)
• iPod touch (2nd generation)
Works with
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
^
¡
: Folder
Folder
CD
(1)
:
A
udiofile
¡!
2
• Update iPod/iPhone software to the latest version.
• Type of control available varies depending
on the type of connected iPod. See
3
¡"
¡#
4
www.kenwood.com/cs/ce/ipod/ for further details.
¡$
5
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
¡%
¡P
* Not supported model KCA-iP500.
• Refer to the web site for connectable iPod and iPod
connection cable.
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
• If you start playback after connecting the iPod, the music
that was playing on the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
⁄
• In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
• You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
About USB device
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Save backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
|
34 KDC-BT50U/ KDC-5047U/ KMR-440U
KDC-BT50U
About “KENWOOD Music Editor”
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
• This unit supports the PC application “KENWOOD
Music Editor Lite ver1.0” or later.
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Lite ver1.0”, you can search a file by title, album or
Version
Profile
Bluetooth Standard Ver. 2.1 + EDR
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phonebook Access Profile)
SYNC (Synchronization Profile)
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
• “KENWOOD Music Editor Lite ver1.0” is available from
the following web site:
For the cell-phones verified for compatibility, access
the following URL:
⁄
• For further information on “KENWOOD Music Editor
Lite ver1.0”, refer to the site above or the application
help.
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
• HFP is a profile used to make a hands-free call.
• OPP is a profile used to transfer data such as a phone book
between units.
KDC-BT50U
About the Bluetooth Audio player
This unit conforms to the following Bluetooth
specifications:
Version
Profile
Bluetooth Standard Ver. 2.1 + EDR
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
⁄
• A2DP is a profile designed to transfer the music from an
audio player.
• AVRCP is a profile designed to control playback and
selection of music by an audio player.
English
|
35
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
The messages shown below display your
systems condition.
TOC Error:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
!
!
• Cannot set up Display.
set to Off.
Error 05:
Error 77:
The disc is unreadable.
• Cannot set up the subwoofer.
• Cannot set up the low pass filter.
• No output from the subwoofer.
On.
The unit is malfunctioning for some reason.
Press the reset button on the unit. If the
“Error 77” code does not disappear, consult
your nearest service center.
Error 99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
the reset button on the unit. If the “Error
99” code does not disappear, consult your
nearest service center.
!
Cannot set up the subwoofer Phase.
set to “Through”.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
IN (Blink):
The CD player section is not operating
properly.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
General
? The Key beep does not sound
The preout jack is being used.
The Key beep cannot be output from the preout
jack.
Protect (Blink): The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
Tuner source
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
? Radio reception is poor.
The car antenna is not extended.
Pull the antenna out all the way.
Unsupported File:
Disc source
An Audio file is played with a format that this
unit can’t support.
? The specified disc does not play, but another one
plays instead.
Copy Protection:
The specified CD is quite dirty.
A copy-protected file is played.
Clean the CD, referring to the CD cleaning of the
Read Error:
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
The disc is severely scratched.
Try another disc instead.
Audio file source
? The sound skips when an Audio file is being
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
played.
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
The recording condition is bad.
Record the media again or use another media.
• An unsupported USB device is connected.
• Connection to the iPod has failed.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 34) for information on supported
iPods.
|
36 KDC-BT50U/ KDC-5047U/ KMR-440U
No Music Data/Error 15:
• The connected USB device contains no
Too Long:
The word or utterance is too long to be
recognized.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
USB ERROR:
iPod Error:
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Record:
The voice tag is not registered in the
phonebook.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Confirm that the software for the iPod is
the latest version.
Favorite: No Memory:
The procedure is not registered to Favorite
Preset Memory
No Access:
No Voice:
The procedure preset with Favorite Control
cannot be available. The preset content may
not be recalled depending on the selected
source or mode.
USB REMOVE (Blink):
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
No call.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Entry:
The cell-phone has not been registered
(pairing).
HF Disconnect: The unit cannot communicate with the cell-
phone.
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Unknown:
The Bluetooth device cannot be detected.
Device Full:
5 Bluetooth device have already been
registered. No more Bluetooth devices are
registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
Too Loud:
English
|
37
Specifications
FM tuner section
CD player section
Frequency range (50 kHz step)
: 87.5 MHz – 108.0 MHz
Laser diode
: GaAlAs
Usable sensitivity (S/N = 26dB)
: 0.7 μV/75 Ω
Digital filter (D/A)
: 8 Times Over Sampling
Quieting Sensitivity (S/N = 46dB)
: 1.6 μV/75 Ω
D/A Converter
: 24 Bit
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Spindle speed
: 500 – 200 rpm (CLV)
Signal to Noise ratio (MONO)
: 65 dB
Wow & Flutter
: Below Measurable Limit
Selectivity (DIN) ( 400 kHz)
: ≥ 80 dB
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Stereo separation (1 kHz)
: 35 dB
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 110 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
MW tuner section
Frequency range (9 kHz step)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 25 µV
LW tuner section
Frequency range
: 153 kHz – 279 kHz
Usable sensitivity (S/N = 20dB)
USB Interface
USB Standard
: USB1.1/ 2.0 (Full speed)
File System
: FAT16/ 32
Maximum Supply current
: 500 mA
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
: 45 µV
Bluetooth section (KDC-BT50U)
Version
: Bluetooth Ver. 2.1 + EDR Certified
Frequency range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication range
: Line of sight approx.10m (32.8 ft)
Profiles
: HFP (Hands Free Profile)
: HSP (Headset Profile)
: SPP (Serial Port Profile)
Audio section
Maximum output power
: 50 W x 4
PWR DIN45324,+B=14.4V
: 30 W x 4
: A2DP (Advanced Audio Distribution Profile)
: AVRCP (Audio/Video Remote Control Profile)
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
: MAP (Message Access Profile )
Speaker Impedance
: 4 – 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 12.5 kHz 8 dB
Preout level / Load (CD)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
|
38 KDC-BT50U/ KDC-5047U/ KMR-440U
Auxiliary input
Frequency response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage
KDC-BT50U : 14.4 V (10.5 – 16V allowable)
KDC-5047U/ KMR-440U
: 14.4 V (11 – 16V allowable)
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
Weight
: 1.3 kg
Specifications subject to change without notice.
English
|
39
This Product is not installed by the manufacturer of a vehicle on the
production line, nor by the professional importer of a vehicle into an EU
Member State.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
Information on Disposal of Old Electrical and Electronic
Equipment and Batteries (applicable for EU countries
that have adopted separate waste collection systems)
• The “AAC” logo is a trademark of Dolby Laboratories.
• iTunes is a trademark of Apple Inc.
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
Products and batteries with the symbol (crossed-out
wheeled bin) cannot be disposed as household waste.
Old electrical and electronic equipment and batteries
should be recycled at a facility capable of handling these
items and their waste byproducts.
Contact your local authority for details in locating a recycle
facility nearest to you.
Proper recycling and waste disposal will help conserve
resources whilst preventing detrimental effects on our
health and the environment.
• iPhone is a trademark of Apple Inc.
• “Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
• “Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
Notice: The sign “Pb” below the symbol for batteries
indicates that this battery contains lead.
The marking of products using lasers
• Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says that the component
uses laser beams that have been classified as Class 1. It means that the
unit is utilizing laser beams that are of a weaker class. There is no danger
of hazardous radiation outside the unit.
This symbol mark indicates that Kenwood
manufactured this product so as to
decrease harmful influence on the
environment.
|
40 KDC-BT50U/ KDC-5047U/ KMR-440U
Magyar
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
•
Alulírott, Kenwood, kijelenti, hogy a jelen KDC-BT50U megfelel az 1999/5/EC
irányelvben meghatározott alapvető követelményeknek és egyéb vonatkozó
előírásoknak.
Svenska
For KDC-BT50U:
Declaration of Conformity with regard to
the R&TTE Directive 1999/5/EC
•
Härmed intygar Kenwood att denna KDC-BT50U stär l överensstämelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
Suomi
Manufacturer:
•
Kenwood vakuuttaa täten että KDC-BT50U tyyppinen laite on direktiivin
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
Slovensko
•
S tem Kenwood izjavlja, da je ta KDC-BT50U v skladu z osnovnimi zahtevami in
ostalimi ustreznimi predpisi Direktive 1999/5/EC.
Slovensky
•
Spoločnosť Kenwood týmto vyhlasuje, že KDC-BT50U spĺňa zákldné požiadavky
a ďalšie prislušné ustanovenia Direktĺvy 1999/5/EC.
English
Dansk
Undertegnede Kenwood erklærer harved, at følgende udstyr KDC-BT50U
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Kenwood ΔΗΛΩΝΕΙ ΟΤΙ KDC-BT50U ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/EK.
•
Hereby, Kenwood declares that this unit KDC-BT50U is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
•
Français
•
Par la présente Kenwood déclare que l’appareil KDC-BT50U est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
•
•
Par la présente, Kenwood déclare que ce KDC-BT50U est conforme aux
exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui
lui sont applicables.
Eesti
Sellega kinnitab Kenwood, et see KDC-BT50U vastab direktiivi 1999/5/EC
põhilistele nõudmistele ja muudele asjakohastele määrustele.
•
Deutsch
Latviešu
•
Hiermit erklärt Kenwood, dass sich dieser KDC-BT50U in Übereinstimmung mit
den grundlegenden Anforderungen und den anderen relevanten Vorschriften
der Richtlinie 1999/5/EG befindet. (BMWi)
•
Ar šo, Kenwood, apstiprina, ka KDC-BT50U atbilst Direktīvas 1999/5/EK
galvenajām prasībām un citiem tās nosacījumiem.
Lietuviškai
•
Hiermit erklärt Kenwood die Übereinstimmung des Gerätes KDC-BT50U mit den
grundlegenden Anforderungen und den anderen relevanten Festlegungen der
Richitlinie 1999/5/EG. (Wien)
•
Šiuo, Kenwood, pareiškia, kad šis KDC-BT50U atitinka pagrindinius Direktyvos
1999/5/EB reikalavimus ir kitas svarbias nuostatas.
Malti
Nederlands
•
Hawnhekk, Kenwood, jiddikjara li dan KDC-BT50U jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/
EC.
•
Hierbij verklaart Kenwood dat het toestel KDC-BT50U in overeenstemming
is met de essentiële eisen en de andere relevante bepalingen van richtlijn
1999/5/EG.
•
Bij deze verklaat Kenwood dat deze KDC-BT50U voldoet aan de essentiële eisen
en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
Українська
•
Компанія Kenwood заявляє, що цей виріб KDC-BT50U відповідає ключовим
вимогам та іншим пов’язаним положенням Директиви 1999/5/EC.
Italiano
•
Con la presente Kenwood dichiara che questo KDC-BT50U è conforme ai
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Turkish
•
Kenwood, işbu belge ile KDC-BT50U numaralı bu ünitenin 1999/5/EC
Direktifi’nin özel gereksinimlerine ve ilgili diğer hükümlerine uygun olduğunu
beyan eder.
Español
•
Por medio de la presente Kenwood declara que el KDC-BT50U cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de
la Directiva 1999/5/CE.
Português
•
Kenwood declara que este KDC-BT50U está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
Polska
•
Kenwood niniejszym oświadcza, że KDC-BT50U spełnia zasadnicze wymogi
oraz inne istotne postanowienia dyrektywy 1999/5/EC.
For Turkey
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli
ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının
Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.
Český
Kenwood timto prohlasuje, ze KDC-BT50U je ve shode se zakladnimi pozadavky
a s dalsimi prislusnymi ustanoveni Narizeni vlady c. 426/2000 Sb.
•
This product complies with Directive, Number 26891
regarding “REGULATION ON THE RESTRICTION OF THE USE
OF CERTAIN HAZARDOUS SUBSTANCES IN LECTRICAL AND
ELECTRONIC EQUIPMENT”.
English
|
41
|