DX-2 Disc Publisher Installation
Quick Reference Guide
Driver Installation:
PrassiTech Zulu2 Installation:
Windows 2000 and Windows XP will find the new hardware and will step you through
the installation process.
For a more in-depth look at the
installation process, please refer to
the Installation section of the User’s
Manual.
1. Click the Next button to begin the Zulu2 installation process.
1. Once the Hardware Setup is complete, verify that the printer is fully powered on
and the connections to the computer are secure.
2. After the installation process completes, remove the check from the Reboot
Computer box and click Finish. Rebooting will occur after installing SureThing.
2. Turn on the computer to which
the DX-2 Disc Publisher is
connected. Once the computer
boots, you will be notified that the
new USB connection has been
found.
SureThing CD Labeler Installation:
1. Click the Start button and select Run from the Start menu. Click the Browse
button and go to the CD/DVD drive, highlight SureThing.exe and click the
Open button, then click OK.
Hardware Setup:
1. Unpack the DX-2 Disc Publisher and place it in the selected workspace. This
space should have enough vertical space to allow for easy loading of media into
the input hopper and have enough room at the back to allow for any rejected
discs to exit the DX-2 Disc Publisher without obstacles.
2. Read the Software License and Warranty information and click the I Accept
button to continue the installation of SureThing.
3. Click the Next button.
3. Click the Next button at the Welcome screen.
4. Place the DX-2 Disc Publisher
Software CD into the CD/DVD
ROM drive.
2. Plug in the power cord to the back of the DX-2 Disc Publisher and turn on the
switch located on the back of the unit. Next, press the power button on the front
panel to turn on the printer.
4. To install to the default directory,
click Next on the Select
Destination Directory screen. If
you wish to install to a different
location, select that location
before clicking Next.
3. Install the Output Bin on the front of the DX-2 Disc Publisher and tightly
secure using the 2 thumbscrews.
5. Windows 2000: Select the option to Search for a suitable driver, and click
Next. Check the CD-ROM Drives Box and click Next. Click the Next button
again when you are notified that the driver has been found.
4. Install the Microboards ink cartridges.
Windows XP: Select the option to Install from a list or specific location and
click Next. Check the Search Removable Media box and click Next.
THE DX-2 DISC PUBLISHER WILL ONLY OPERATE WITH
MICROBOARDS INK CARTRIDGE MODELS PRF19ML AND PRF38ML.
5. Select adding a desktop
shortcut and the location in which
the Start Menu shortcut will be
created, or make no changes to
select the default locations.
Click Next when the locations
are suitable.
6. The Digital Signature screen will appear. Click the Yes button at the bottom of
A. Remove the tape from the front of the DX-2 Disc Publisher, lift the lid, and
remove the tape from the print carriage once it has moved to the center of the
printer.
the screen. The drivers will then be copied to the hard drive.
7. Once the USB drivers have been copied, click the Finish button.
B. Raise the cradle latches. Remove the ink cartridges from the packaging
and carefully remove the plastic tape covering the print head.
8. The Print driver installation will occur next. Repeat steps 3 through 7 to install
the print drivers.
6. Click Start on the next screen to install the application.
C. Gently push the ink cartridges into the appropriate cradles. Do not try to
force the cartridges into place as doing so may damage the cartridge.
9. Verify the installation of the DX-2 Disc Publisher by clicking the Start button.
Select Printers and Faxes from the Start menu, either through the Settings
menu for Windows 2000 or directly in the Start menu for Windows XP. You will
see the new printer installed and available for use.
7. Click Finish once the installation is complete. You will also have the opportunity
D. Secure the cradle latches and close the lid. The print carriage will return to
the right neutral position.
to register the software on-line.
8. The driver and software installation is now
complete. The computer will need to be
rebooted for the software to operate correctly.
Click OK to reboot. If you choose not to reboot
at this time, click the Cancel button to reboot
later. Remember, the computer must be
rebooted prior to running the DX-2 Disc
Publisher, Zulu2, or SureThing.
5. Connect the DX-2 Disc Publisher to the computer using the USB cable provided.
Please be sure the computer is off during this process.
DX-2 Disc Publisher controller and Software Installation:
A. Plug the small end of the USB cable into the back of the DX-2 Disc Publisher.
The DX-2 Disc Publisher controllers, PrassiTech Zulu 2, and SureThing Disk Labeler
are included on the Software disc.
B. Plug the larger end of the USB cable into an available port on the
PC. Confirm that both ends of the cable are securely connected.
USB 2.0 support on the PC is required.
DX-2 Disc Publisher Controller Installation:
6. Turn the PC on at this point.
1. Click the Start button and select Run from the Start menu. Click the Browse
button and go to the CD/DVD drive, highlight Publisher.exe, click the Open
button, then click OK.
The Hardware Setup is now complete. Proceed to the installation of the DX-2 Disc
Publisher Drivers and Software.
Installation of the DX-2 Disc Publisher is complete. After rebooting,
the printer will need to be aligned and the robotics configured prior
to burning and printing disks. Please see the DX-2 Disc Publisher
Configuration Quick Reference Guide on the other side of this page,
or refer to the appropriate sections of the User’s Manual.
2. Click the Next button on the next window. Once the window reads Ready to
Install the Program, click the Install button. Click Finish once the installation
completes. The Zulu2 software installation will begin automatically.
820-00134-02
|