4
PLC CPUs
IC697CSE925
62
64 MHz, 32-Bit Floating Point Central Processing Unit
1 Mbyte Memory, State Logic
GFK-1167B
August 1997
64 MHz, 32-Bit Floating Point Central Processing Unit 1 Mbyte Memory, State Logic (IC697CSE925)
datasheet GFK-1167B
a45242
Features
SupportsState Logiccontrolprogramming
Supportsfloatingpointcalculations
Single slot CPU.
12K inputs and outputs (any mix).
Up to 8Kanalog I/ O.
OK
RUN
ENABLED
B
A
T
T
E
R
0.4microseconds per boolean function.
64MHz,80486DX2microprocessor.
SupportsIC660/ IC661andIC697I/ Oproducts.
MEM PROTECT
CSE 925
STATE LOGIC
CPU
TOP
Y
Programmed by AD641 and IC641 (MS-DOS ) software
products.
OFF
ON
Provides 1 Mbyte of battery-backed memory in the same
slot.
REMOTE PROGRAMMER
MEMORY PROTECT
KEY POSITION
Configurabledata and program memory.
Battery-backed calendar clock.
FRONT
MODULE OK
RUN
OUTPUTS
ENABLED
Three position operation mode switch.
Password controlled access.
MEMORY
PROTECT
REMOTE
PROGRAMMER
ONLY
ON = OK, ENABLED,
PROTECTED
Remoteprogrammer keyswitchmemory protection
Four status LEDs.
Software configuration (No DIP switches or jumpers to
set).
RUN WITH
OUTPUTS
ENABLED
RUN WITH
OUTPUTS
DISABLED
STOP
Referenceinformation inside front door.
In-system upgradablefirmware.
BATTERY
CONNECTORS
Functions
INSTALL NEW
BATTERY BEFORE
UNPLUGGING OLD
BATTERY. USE
IC697ACC701
The CSE 925 is a single slot programmable controller
CPU which provides State Logic control programming
and floating point calculations. The CSE 925 can be
programmed in State Logic, Relay Ladder Logic, and
C to perform real-time control of machines, processes,
and material handling systems.
MODULE FUNCTION
64 MHz 32 BIT CENTRAL
PROCESSING UNIT WITH
FLOATING POINT MATH
COPROCESSOR, IN-SYSTEM
UPGRADABLE FIRMWARE
SERIAL PORT
The AD641 software products are used to program
the CSE 925 in State Logic; the IC641 (MS-DOS) soft-
ware products are used to program in Relay Ladder
Logic and C. The IC641 (MS-DOS) software is also
used to perform all configuration functions for the
CSE 925.
RS-485
COMPATIBLE
USE THIS MODULE
IN SLOT 1 ONLY.
MODULE
IC697CSE925
LABEL
44A726758-148R01
The CSE 925 communicates with I/ O and smart op-
tion modules over the rack mounted backplane
(IC697CHS750, 782, 783, 790, 791) by way of the VME
C.1 Standard format.
MS-DOS is a registered trademark of Microsoft Corporation.
3
PLC CPUs
GFK-1167B
August 1997
64 MHz, 32-Bit Floating Point Central Processing Unit
1 Mbyte Memory, State Logic
Make sure that rack power is off.
Serial Port
Install the CSE 925 module in slot 1 of rack 0 (see
Figure 2).
The 15-pin D-connector provides the connection to an
RS-485 compatible serial port on the CPU as shown in
Figure 2.
Turn on power.
The module should power up and the top LED should
blink. When the diagnostics have completed successfully,
the top LED stays on and the second and third LEDs are
off. The fourth LED is off if the keyswitch is in the OFF
position. The CPU is now ready to be programmed.
The serial connection is made from the serial port on the
CPU to the serial port on the programming computer,or
other serial device, through the RS-422/ RS-485 to
RS-232 Converter (IC690ACC900) or RS-232 to RS-422
Miniconverter (IC690ACC901). This connection can be
made with available cables or you may build cables to fit
the needs of your particular application. See reference
3 for more information on serial communications.
After the program has been verified the toggle switch may
be moved to the appropriate operation mode position.
The LEDs indicate the position of the toggle switch,
memory protection status, and the state of the program.
Configuration
The IC641 (MS-DOS) software is also used to load the State
Logic operating system into the CSE 925 CPU module.
The operating system is provided on a floppy disk with
the CSE 925. The operating system is stored in flash
memory on the module. For information on loading the
operating system, see the State Logic Control System User’s
Manual.
The IC697CPU and I/ O system isconfigured with IC641
(MS-DOS) programming software. There are no DIP
switches or jumpers used to configure the system. The
CPU verifies the actual module and rack configuration
at power-up and periodically during operation. The
actual configuration must be the same as the
programmed configuration. Deviations are reported to
the CPU alarm processor function for configured fault
response. Consult Reference 1 for a description of
configuration functions.
SERIAL
a45301
RACK 0
PROGRAMMER
P
S
C
P
U
B
T
M
P
C
M
G
B
C
Batteries
or
A lithium battery (IC697ACC701) is installed as shown
in Figure 1. This battery maintains program and data
memory when power is removed and operates the
calendar clock. Be sure to install the new battery before
removing the old battery. Specific indication of a low
battery state is detailed in Reference 2.
N
B
C
*
ONE
METER
IC66* I/O BUS (7500 FEET (2285 METERS) MAXIMUM)
RACK 1
B
R
M
Removing a Module
The instructions below should be followed when
removing a module from its slot in a rack.
IC66*
I/O BLOCK
NOTE
Grasp the board firmly at the top and bottom of
the board cover with your thumbs on the front of
the cover and your fingers on the plastic clips on
the back of the cover.
RACK 7
TOTAL LENGTH OF ALL INTERCONNECTING
CABLES FROM BTM TO LAST BRM IS
50 FEET(15 METERS) MAXIMUM. ALL RACKS
MUST BE AT SAME GROUND POTENTIAL
(8 RACKS MAXIMUM).
B
R
M
FORCED AIR COOLING REQUIRED FOR
PROPER OPERATION. REFER TO TEXT.
*
Squeeze the rack clips on the back of the cover
with your fingers to disengage the clip from the
rack rail and pull the board firmly to remove it
from the backplane connector.
RACK FAN ASSEMBLY IC697ACC721/724
AVAILABLE FOR DIRECT MOUNTING ON
RACK.
TERMINATOR PLUG (IC697ACC702)
Figure 2. System Configuration, Serial Connection to
Programmer
Slide the board along the card guide and remove
it from the rack.
4
PLC CPUs
GFK-1167B
August 1997
64 MHz, 32-Bit Floating Point Central Processing Unit
1 Mbyte Memory, State Logic
Table 1. References
Reference
Title
1
2
3
4
Programming Software User’s Manual
Programmable Controller Reference Manual
Programmable Controller Installation Manual
State Logic Control System User’s Manual
Table 2. Specifications for IC697CSE925
Battery
Shelf life
10 years at 20 C (68 F)
Memory retention
6 months nominal without applied power.
Current required from 5V bus
3.3 Amps nominal
Time of Day Clock accuracy
Elapsed Time Clock (internal timing) accuracy
" 3.5 seconds per day maximum
" .01% maximum
Serial Port
RS422/485 compatible
ProgrammerSerialAttachment
VME
System designed to support the VME standard C.1
Refer to GFK-0867B,or later for product standards and generalspecifications.
Table 3. Ordering Information
Description
Catalog Number
Central Processing Unit - 64 MHz, 32-Bit,
Floating Point, 1 Mbyte Memory, State Logic
IC697CSE925
Lithium Battery
IC697ACC701
Rack Fan Assembly, 120 VAC
Rack Fan Assembly, 240 VAC
IC697ACC721
IC697ACC724
Note: For Conformal Coat option, or Low TemperatureTesting option please
consult the factory for price and availability.
|