User’s Guide
L601 / L602 / L603 / L604 / L605
L601M / L602M / L603M / L604M / L605M
DECT 6.0 Digital Cordless Phone
Warning
Use only the adapter and telephone line cord provided
in the box.
This User's Guide provides you with all the information you need to
get the most from your phone.
Before you make your first call you will need to set up your phone.
Follow the simple instructions in 'Getting Started', on the next few
pages.
IMPORTANT
Only use the telephone line cord supplied.
This equipment is not designed to make emergency telephone calls during power failures. Alternative
arrangements should be made for access to emergency services.
Got everything?
•
•
•
•
•
•
•
•
Handset
Base
NiMH Rechargeable Battery Pack
Battery Door
Power Adapter
Telephone Line Cord
User's Guide
Quick Start Guide
In multi-handset packs, you will find one or more additional handsets, chargers with power adapter
units, additional rechargeable battery packs and battery doors.
3.10 Storing a phonebook entry as a
1. Getting started ................................................6
1.1 Connecting the base........................................... 7
1.2 Installing and charging the handset
one touch number .............................................14
3.11 Dialing from the phonebook ..............................15
3.12 Caller ID ............................................................15
3.12.1 Calls List ................................................15
3.12.2 Viewing the calls list ...............................16
3.12.3 Saving a number from the calls list
battery pack........................................................ 7
1.3 Assembling the rubber band of cordless
handset (Not applicable for L60xM models)....... 8
1.4 Setting the display language .............................. 8
1.5 Setting the date and time.................................... 9
to the phonebook ...................................16
3.12.4 Deleting a calls list entry ........................16
3.12.5 Deleting the entire calls list ....................16
3.13 Personal Settings ..............................................17
3.14 Intercom ............................................................18
3.14.1 Calling another handset .........................18
3.14.2 Transferring a call to another
2. Getting to know your phone..........................9
3. Using the phone............................................13
3.1 Making a call..................................................... 13
3.2 Speed dial calling ............................................. 13
3.3 Answering a call ............................................... 13
3.4 Ending a call..................................................... 13
3.5 Adjusting volume .............................................. 13
3.6 Muting a call ..................................................... 14
3.7 Dialing from the redial list ................................. 14
3.8 Dialing from the calls list................................... 14
3.9 Adding an entry to the phonebook.................... 14
handset ..................................................18
3.14.3 Three-party conference call ...................19
3.15 Setting the dial mode.........................................19
3.16 Setting the flash time.........................................19
3.17 Setting the area code ........................................20
4
3.18 Registration .......................................................20
3.18.1 Registering a handset ............................20
3.19 Resetting all settings .........................................21
3.20 Paging/Finding a handset..................................21
4. Help................................................................21
5. General information .....................................23
5
HANDSET RANGE
1. Getting started
WARNING
Do not place your phone in the bathroom or other humid
areas.
Optimal range is reached when there are no other electrical
appliances working within the range area. Any obstruction
between the base and handset will also reduce the range
significantly.
SIGNAL STRENGTH
Location
When out of range of the corded base, the screen shows OUT
OF RANGE. If you are on a call, the line will hang up. Move
back within in range. The cordless handset will automatically
re-connect to the corded base.
When choosing a location for your new phone, here are
some important guidelines you should consider:
•
•
Avoid sources of noise and heat, such as motors,
fluorescent lighting, microwave ovens, heating
appliances and direct sunlight.
Avoid areas of excessive dust, moisture and low
temperature.
Setting up
IMPORTANT
The base must be plugged into an electrical outlet at all
times. Do not connect the telephone line cord into the
telephone wall jack until the handset is fully charged. Only
use the adapter and telephone line cord supplied with the
product.
•
•
•
Avoid other cordless telephones or personal computers.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
Never touch non-insulated telephone wires or terminals,
unless the telephone line has been disconnected at the
network interface.
•
WHICH POWER ADAPTER?
The power adapter with the smaller pin is for the base unit
and the power adapter with the larger pin is for the charger
unit (only for multi-handset packs).
•
Use caution when installing or modifying telephone lines.
6
Getting started
1.1
Connecting the base
1.2
Installing and charging the handset
battery pack
1. Plug the power adapter and the telephone line cord into
the base. The power adapter with the larger pin is for
the charger (only in multi-handset packs).
2. Plug the other end of the power adapter into a power
outlet and the telephone line cord into a telephone wall
jack.
1. Slide off the battery compartment cover to remove it.
Place the supplied rechargeable battery pack in the
battery compartment, with the battery connector
plugged in, as shown.
3. Use only the provided power adapter.
Getting started
7
2. Slide the battery compartment cover back on.
3. Put the handset on the base to charge for at least 24
hours. Once charged, the will indicate that the
handset is fully charged.
2. Press and smooth out the rubber band to enwrap the
handset firmly.
IMPORTANT
Use only the rechargeable battery pack provided with the
product.
1.3
Assembling the rubber band of
cordless handset (Not applicable for
L60xM models)
If you have purchased additional rubber band(s) of the
cordless handset separately, refer to the following steps for
replacement. To remove the originally installed rubber band,
dig out the rubber band from handset bottom gap and then
take it off from handset around.
1.4
Setting the display language
1. Press MENU and then VOL+ or REDIAL/VOL- to select
SETUP HS
.
1. To assemble the rubber band, align the protuberant pins
of the rubber band with the holes around of the handset
sides and click the rubber band into place. Respect the
direction, side with gap should be attached to the
handset bottom, as shown.
2. Press MENU and then VOL+ or REDIAL/VOL- to select
LANGUAGE
.
3. Press MENU and then VOL+ or REDIAL/VOL- to select
the desired language.
4. Press MENU to save.
8
Getting started
1.5
Setting the date and time
2. Getting to know your phone
Overview of your handset
1. Press MENU and then VOL+ or REDIAL/VOL- to select
DATE&TIME. If you're a subscriber to your network's Caller
ID service, the date and time is automatically set when a
call is received.
2. Press MENU and then use the keypad to edit the year
and the date.
3. Press VOL+ or REDIAL/VOL- or
or CID to move
between the input fields YEAR and DATE
.
4. Press MENU and then use the keypad to edit the time in
12 HR format. Press VOL+ or REDIAL/VOL- to toggle
AM/PM settings.
5. Press MENU to save the settings.
Your phone is now ready for use.
Getting to know your phone
9
Get acquainted with the following 14 buttons on your
handset and their multi-function tasks.
4
Talk off / Back
a) In menu / editing mode: Press to exit to previous level.
b) In pre-dial mode / phonebook / calls list / redial list
entry: Press to exit to idle.
1
Scroll up / Volume up
a) In menu mode: Press to scroll up.
c) During ringing: Press to silence the incoming ringer
temporarily.
d) During a call: Press to end a call.
Alphanumeric keypad
a) In idle / pre-dial / editing mode / during a call: Press to
enter characters / numbers.
b) In editing mode: Press to move the cursor to the left.
c) During a call: Press to increase the volume.
d) Calls list / phonebook / redial list entry: Press to scroll
up the list.
5
6
2
Menu / Select
a) In idle mode: Press to access menu list.
b) In idle mode: Press and hold to activate speed dial.
b) In menu / editing mode: Press to confirm and save the
settings.
c) During a call: Press to transfer the call to another
handset.
d) In calls list entry: Press to save the entry to the
phonebook.
e) In phonebook entry: Press to go to sub-menus of
phonebook.
#/Pause / ABC / Format
a) In idle / pre-dial / number editing mode / during a call:
Press to insert a "#", press and hold to insert a pause (P).
b) In name editing mode: Toggle ABC/abc. Press and hold
to insert a space.
c) In calls list entry: Press to toggle Caller ID display
format between 7, 8, 10 and 11 digits when returning calls
from Caller ID list.
d) In phonebook list entry: If the number is more than 15
digits, press to view the next page of remaining digits.
3
Right / Calls list
a) In idle mode / during a call: Press to access calls list.
b) In editing mode: Press to move the cursor to the right.
7
8
Intercom
a) In idle mode / during a call: Press to initiate an intercom
call.
Microphone
10
Getting to know your phone
9
Speaker
12 Talk On / Flash
a) In idle / pre-dial mode: Press to make a call with the
a) In idle / pre-dial mode: Press to make a call.
b) Calls List / phonebook / redial list entry: Press to make
a call to the selected entry.
speakerphone.
b) During a call: Press to toggle between the speakerphone
and the earpiece.
c) Calls List / phonebook / redial list entry: Press to make
a call with the speakerphone.
c) During a call: Press to switch another call.
d) During an incoming call: Press to answer a call.
13 Left / Phonebook
d) During ringing: Press to answer a call with the
speakerphone.
a) In idle mode / during a call: Press to access the
phonebook.
10 */Tone
b) In editing mode: Press to move the cursor to the left.
a) In idle / pre-dial / editing mode: Press to insert a *.
14 Mute / Clear / Back / X
b) During a call: Press to switch from pulse to tone dialing
temporarily if pulse mode was selected before. After the
call has ended, the dial mode will change back to pulse.
c) In phonebook list entry: If the number is more than 15
digits, press to view the previous page of remaining digits.
a) In menu / phonebook entry mode: Press to exit to the
previous level.
b) In pre-dial / editing mode: Press to delete one character /
digit. Press and hold to delete all characters / digits.
11 Scroll Down / Volume Down / Redial List
a) In idle mode: Press to access the redial list.
b) In menu mode: Press to scroll down.
c) During a call: Press to mute / unmute the call.
d) In calls list entry: Press to delete the entry. Press and
hold to delete all call log entries.
c) In editing mode: Press to move the cursor to the right.
d) During a call: Press to decrease the volume.
e) Calls list / phonebook / redial list entry: Press to scroll
down the list.
Getting to know your phone
11
On when a call is muted.
Full battery power level.
Cordless Handset LCD Display
2/3 battery power level.
1/3 battery power level.
Flashes when low battery level is detected, needs
charging.
Animation in cycle. Battery is charging.
Display Icons
In idle mode, the current time is displayed.
In Caller ID mode, the time of call is displayed.
On when speakerphone is turned on.
Indicates when new call is received.
Off when new call has been viewed.
On when the line is in use.
Flashes when there is an incoming call.
On when ringer volume is turned off.
On when there is received new voice mail not yet
listened to.
Off when new voice mail has been listened to.
In idle mode the current date is displayed.
In Caller ID mode, the date of the call is displayed.
12
Getting to know your phone
Overview of the base
3. Using the phone
3.1
Making a call
1. Enter the phone number and then press
/FLASH or
/SPEAKER to dial the phone number.
3.2
Speed dial calling
1. In idle mode, press and hold a key from
/1 to
WXYZ/9 until the number is displayed and dialed.
3.3
Answering a call
1
Find
1. Press
/FLASH or
/SPEAKER to answer the
a) Press to find/page all registered handsets. Press the button
again, or any key on the handset, to turn off page signal.
incoming call.
3.4
Ending a call
1. During a call, press
/BACK or put the handset on
the base.
3.5
Adjusting volume
1. During a call, press VOL+ or REDIAL/VOL- to adjust
the volume.
Using the phone
13
3.6
Muting a call
3.9
Adding an entry to the phonebook
1. During a call, press MUTE to mute the microphone, so
that you can talk to someone else in the room without
your caller hearing you.
1. Press
.
2. Press MENU and then VOL+ or REDIAL/VOL- to scroll
and select ADD
3. Press MENU and then enter the name.
4. Press MENU and then enter the number.
5. Press MENU to save.
.
2. Press MUTE again to unmute.
3.7
Dialing from the redial list
1. Press REDIAL/VOL- and then VOL+ or REDIAL/VOL-
NOTE
to scroll and select an entry you want to redial.
Numbers can be up to 24 digits long and names up to 16
characters long. Entries are stored in alphabetical order.
2. Press
/FLASH or
/SPEAKER to dial the number.
3.10 Storing a phonebook entry as a one
touch number
3.8
Dialing from the calls list
1. Press CID and then VOL+ or REDIAL/VOL- to select
1. Press
.
the entry you want to dial.
2. Toggle the #/
/PAUSE/FORMAT key to format the
2. Press MENU and then VOL+ or REDIAL/VOL- to select
SPEED DIAL
.
dialing number.
3. Press MENU and then VOL+ or REDIAL/VOL- to select
3. Press
/FLASH or
/SPEAKER to dial the number.
the speed dial key from /1 to WXYZ/9.
4. Press MENU and then VOL+ or REDIAL/VOL- to scroll
to the entry you want.
5. Press MENU to save.
14
Using the phone
•
Information about incoming calls will vary by country and
network operator. Some operators may charge a
subscription for their Caller ID service.
3.11 Dialing from the phonebook
1. Press
and then VOL+ or REDIAL/VOL- to scroll
and select the entry you want to dial.
3.12.1 Calls List
2. Press
/FLASH or
/SPEAKER to dial the number.
The calls list contains details of missed and received calls.
Details include the date and time of the call. Entries are
displayed in chronological order with the most recent call at
the top of the list.
TIPS
Instead of scrolling to browse the phonebook entries, press
the numeric key corresponding to the first letter of the entry
you wish to locate. For example, pressing 2 will show the
entries starting with A. Pressing 2 again will show the entries
starting with B, etc.
NOTE
•
When the calls list is full, a new call replaces the oldest
one in the list.
3.12 Caller ID
•
•
Details of up to 30 calls may be stored.
If you have subscribed to Caller ID service, and provided the
identity of the caller is not withheld, the number of the caller
will be displayed together with the date and time of the call
(if provided by the network).
If you receive more than one call from the same number,
only the most recent call is kept in the calls list. When
you have missed calls (incoming calls that you haven't
answered) the
on all handsets registered to the base. If one handset is
used to view the calls log, the icon on the other
handsets remains on (for multi-pack use only).
icon will be displayed in the display
NOTE
•
If the telephone number is not available for incoming
calls, the handset will display UNAVAILABLE
If the incoming call is from a withheld telephone number,
the handset will display PRIVATE
.
•
.
Using the phone
15
3.12.2 Viewing the calls list
1. Press CID to enter the calls list.
2. Scroll VOL+ or REDIAL/VOL- to browse the calls list.
NOTE
3.12.3 Saving a number from the calls list to the
phonebook
1. Press CID to enter the calls list.
2. Press VOL+ or REDIAL/VOL- to select the entry you
want.
3. Press MENU and then enter the name if desired.
4. Press MENU and then edit the number if desired.
5. Press MENU to save.
•
When reviewing an entry from the calls list, press #/
PAUSE/FORMAT repeatedly to display the number in
different format.
/
For example, if a caller number is displayed as
888-331-3383, the various formats will be:
331-3383
1-331-3383
888-331-3383
3.12.4 Deleting a calls list entry
1. Press CID to enter the calls list.
2. Press VOL+ or REDIAL/VOL- to scroll to the entry you
want.
1-888-331-3383
3. Press MUTE to delete the entry.
You may choose the desired number format for local and
long distance numbers before dialing or saving it into the
phonebook.
3.12.5 Deleting the entire calls list
1. Press CID to enter the calls list.
•
The
viewed.
icon is removed once the new call has been
2. Press and hold MUTE. DELETE ALL CALL LOG ENTRIES? is
displayed.
3. Press MENU to confirm. All entries will be deleted.
NOTE
You need to review a call before you delete the record from
the call list.
16
Using the phone
3.13 Personal Settings
Menu map
MAIN MENU
DATE & TIME
PHONEBOOK
SETUP HS
SETUP BS
RESET SETTINGS
SUB MENU
YEAR
DATE
TIME
VIEW
RINGER TONE
RINGER VOLUME
KEY TONE
DIAL MODE
FLASH TIME
AREA CODE
CLR VOICE MAIL
ALL SETTINGS
ADD
EDIT
DELETE
DELETE ALL
PB CAPACITY
SPEED DIAL
LOW BATT TONE
OUT RANGE TONE
HANDSET NAME
LANGUAGE
LCD CONTRAST
REGISTRATION
Using the phone
17
1. Press MENU.
3.14.1 Calling another handset
2. Press VOL+ or REDIAL/VOL- to scroll through the
menu.
3. Press MENU for opening sub-menus and/or saving.
1. Press INT. Except for the originating handset, all
registered handsets will be displayed in the list.
2. Press VOL+ or REDIAL/VOL- to select the handset you
want to call.
Press MUTE to go back to the previous menu level or cancel
an action.
3. Press MENU to call the handset.
4. Press
/BACK to hang up.
If you do not press any button on the handset for 30 seconds,
the display will automatically return to standby. It will also
return to standby when the handset is placed on the base or
charger.
NOTE
If the handset is not within the valid operation range, this
function may not be available. During an intercom call, you
will hear an alert tone if there is an incoming external call.
You need to press
before answering the incoming external call.
/BACK to hang up the intercom call
3.14 Intercom
This feature is only available when there are at least two
registered handsets. It allows you to make internal calls,
transfer external calls from one handset to another handset,
and use the conference option.
3.14.2 Transferring a call to another handset
1. During an external call, press INT.
- Your call is put on hold.
2. Press VOL+ or REDIAL/VOL- to select the handset you
want to call.
3. Press MENU to call the handset.
18
Using the phone
4. When the other handset answers by pressing
/FLASH
3.15 Setting the dial mode
The default dialing mode is suitable for your country and
network operator. It is unlikely that you should need to
change this setting unless advised to do so.
or /SPEAKER, press /BACK to transfer the
call. If the other handset does not answer, press MUTE
to talk to your caller again.
3.14.3 Three-party conference call
1. During an external call, press INT.
- Your caller is put on hold.
2. Press VOL+ or REDIAL/VOL- to select the handset you
want to call.
3. Press MENU to call the handset.
4. When the other handset answers the intercom call,
press MENU on the calling handset to set up the
conference call.
1. Press MENU and then VOL+ or REDIAL/VOL- to select
SETUP BS
.
2. Press MENU to select DIAL MODE
.
3. Press MENU and then VOL+ or REDIAL/VOL- to select
TONE or PULSE
.
4. Press MENU to save.
NOTE
If the pulse mode is selected, press TONE/* to switch from
pulse to tone dialing temporarily when dialing out. After the
call is ended, the dial mode will change back to pulse.
5. Press
/BACK on any handset to end a three-party
conference call and leave the other handset engaged
with the caller.
3.16 Setting the flash time
The default flash time is 600MS. It is unlikely that you should
need to change this setting unless advised to do so.
NOTE
During an external call, pressing
/FLASH or
/
SPEAKER on any handset will join in the call and set up a
conference call.
1. Press MENU and then VOL+ or REDIAL/VOL- to select
SETUP BS
.
Using the phone
19
2. Press MENU and then VOL+ or REDIAL/VOL- to select
To register an additional handset,
FLASH TIME
.
1. Press MENU and then VOL+ or REDIAL/VOL- to select
3. Press MENU and then VOL+ or REDIAL/VOL- to the
flash time you want. (8 options are available : 90 100, 110,
250 300, 400, 600 and 700MS)
4. Press MENU to save.
SETUP HS
.
,
2. Press MENU and then VOL+ or REDIAL/VOL- to select
,
REGISTRATION
.
3. Press MENU and then VOL+ or REDIAL/VOL- to select
YES or NO
.
3.17 Setting the area code
1. Press MENU and then VOL+ or REDIAL/VOL- to select
4. Select YES then press MENU to enter the registration
procedure as follows:
SETUP BS
.
1. Press and hold FIND for around 4 seconds on the base.
2. Place the unregistered cordless handset on the base
or charger.
2. Press MENU and then VOL+ or REDIAL/VOL- to select
AREA CODE
.
3. Press MENU and then enter the area code.
3. A confirmation tone is generated if registration is
4. Press MENU to save.
successful. HANDSET X is displayed where
X
denotes
3.18 Registration
3.18.1 Registering a handset
the number of handsets, and then the phone returns
to idle.
Up to 5 handsets can be registered to one base. The original
handset is pre-registered to use. Additional handsets must
be registered to the base before you can use them.
To register an originally unregistered handset, follow steps 1
through 3 above.
20
Using the phone
3.19 Resetting all settings
1. Press MENU and then VOL+ or REDIAL/VOL- to select
4. Help
The icon is not scrolling when the handset is
placed on the base
RESET SETTINGS
.
2. Press MENU and then VOL+ or REDIAL/VOL- to select
•
•
•
Handset not properly seated on the base cradle -readjust
the handset on the base.
Dirty contact - clean the charge contacts by wiping with
an alcohol moistened cloth.
ALL SETTINGS
.
3. Press MENU to select YES. All personalized settings will
be reset to default.
NOTE
All of your phonebook entries, calls list, and redial list, will
remained unchanged.
Battery is full - charging is not necessary at this time.
No dial tone
•
If there is no base power, check the connections. Reset
the phone by unplugging then plugging it back into an
electrical outlet.
3.20 Paging/Finding a handset
Press FIND on the base. All handsets registered to the base
will ring.
•
If the handset batteries are empty, recharge the battery
pack for at least 24 hours.
•
•
Move the handset closer to the base.
Be sure to use only the provided telephone cords.
To stop the paging, press FIND again, or press any key on
the handset, or place the handset on the base.
Poor audio quality
•
If the base is too close to electrical appliances, reinforced
concrete walls, or metal door frames, move the base
from these areas.
Help
21
No ring tone
If the handset disconnects from the base during a
phone call
•
•
The ringer may be off.
•
•
•
•
Check that the power cord is connected properly into the
base.
The volume may need to be increased.
Caller ID does not work
Check that the power adapter is connected properly into
the electrical outlet.
Move the handset closer to the base. It may be out of
range.
Reset the base by unplugging the unit's electrical power.
Reset the handset by unplugging and re-plugging its
battery pack. Wait for around 15 seconds and re-plug the
power again. Allow up to one minute for the handset to
synchronize with the registered base again.
•
•
Check your subscription with your network operator.
If you subscribe to high-speed internet service (Digital
Subscriber Line - DSL) through your telephone lines, you
must install a DSL filter between the telephone base and
the telephone wall jack. The filter will prevent noise and
caller ID problems caused by DSL interference. Please
contact your DSL service provider for more information
about DSL filters.
A phonebook entry cannot be stored
The phonebook is full. Delete an entry to free memory.
Noise interference on your radio or television
•
•
Your base or charger may be too close. Move it as far
away as possible.
No display
•
•
•
Try recharging or replacing the rechargeable battery
pack.
Reset the base. Unplug the unit's electrical, then plug it
back in.
If the LED is not lit up, then try to unplug the unit's
electrical power, and then plug it back in.
22
Help
4. Do not allow anything to rest on the power cord. Place
the power cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents
as that may result in fire or electric shock.
6. Unplug this product from the electrical outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
7. Do not disassemble this product. If service or repair
work is required, contact the customer service helpline
found in this User's Guide.
5. General information
If your product is not working properly...
1. Read this User's Guide.
3. Contact Customer Service in the US and Canada at
1-888-331-3383.
To order a replacement battery pack contact customer
service or visit our website.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge
protector to protect the equipment.
10. Do not use this phone to report a gas leak, especially if
you are in the vicinity of the gas line.
Important safety instructions
Follow these safety precautions when using your phone to
reduce the risk of fire, electric shock, and injury to persons
or property:
1. Keep all vents and openings of the phone unblocked.
Do not set the phone on a heating register or over a
radiator. Ensure that proper ventilation is provided at the
installation site.
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger UL
Listed or CSA Certified Telecommunication Line Cord.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a
bath tub, kitchen sink, or swimming pool).
General information
23
5. Do not place this product on an unstable cart, stand, or
table. This product may fall, causing serious damage to
the product.
6. Adjust only those controls that are covered by the
operating instructions. Improper adjustment of other
controls may result in damage and will often require
extensive work to restore the product to normal
operation.
7. Clean this product with a soft, damp cloth. Do not use
chemicals or cleaning agents to clean this phone.
8. Use only the power supply that came with this unit.
Using other power supplies may damage the unit.
9. Because this phone operates on electricity, you should
have at least one phone in your home that operates
without electricity in case of a power outage.
10. To avoid interference to nearby appliances, do not place
the base of the phone on or near a TV, microwave oven,
or VCR.
Unplug this cordless phone immediately
from an outlet if:
•
•
•
The power cord or plug is damaged or frayed.
Liquid has been spilled on the product.
The product has been exposed to rain or water. Do not
retrieve the handset or base until after you have
unplugged the power and phone from the wall. Then
retrieve the unit by the unplugged cords.
The product has been dropped or the cabinet has been
damaged.
•
•
The product exhibits a distinct change in performance.
Installation Guidelines
1. Read all instructions and save them for future reference.
2. Follow all warnings and instructions marked on the
product.
3. Do not install this product near a bath tub, sink, or shower.
4. Operate this phone using only the power source that is
indicated on the marking label. If you are unsure of the
power supply to your home, consult with your dealer or
local power company.
CAUTION
To maintain compliance with the FCC's RF exposure
guidelines, place the base unit at least 20 cm from nearby
persons.
24
General information
Battery Safety Instructions
Consumer Products and Accessories
•
Do not burn, disassemble, mutilate, or puncture the
battery. The battery contains toxic materials that could be
released, resulting in injury.
Limited Warranty ("Warranty")
Thank you for purchasing this Motorola branded product
manufactured under license by Binatone Electronics
International LTD ("BINATONE").
CAUTION
There is a risk of explosion if you replace the battery with an
incorrect battery type. Use only the battery pack that came
with your phone or an authorized replacement
recommended by the manufacturer.
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE
warrants that this Motorola branded product ("Product") or
certified accessory ("Accessory") sold for use with this
product that it manufactured to be free from defects in
materials and workmanship under normal consumer usage
for the period outlined below. This Warranty is your exclusive
warranty and is not transferable.
•
•
•
Keep battery packs out of the reach of children.
Remove battery packs if storing over 30 days.
Do not dispose of battery packs in fire, which could result
in explosion.
•
The rechargeable battery packs that power this product
must be disposed of properly and may need to be
recycled. Refer to the battery label for battery type.
Contact your local recycling center for proper disposal
methods.
Who is covered?
This Warranty extends only to the first consumer purchaser,
and is not transferable.
SAVE THESE INSTRUCTIONS
General information
25
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT OR ACCESSORY,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS
OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS
OF INFORMATION OR OTHER FINANCIAL LOSS
ARISING OUT OF OR IN CONNECTION WITH THE
ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
What will BINATONE do?
BINATONE or its authorized distributor at its option and
within a commercially reasonable time, will at no charge
repair or replace any Products or Accessories that does not
conform to this Warranty. We may use functionally
equivalent reconditioned/ refurbished/ pre-owned or new
Products, Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR
OR REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or
exclusions may not apply to you. This Warranty gives you
specific legal rights, and you may also have other rights that
vary from one jurisdiction to another.
26
General information
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b)
contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes
or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of
MOTOROLA or BINATONE., are excluded from coverage.
Products Covered
Length of Coverage
Consumer Products
One (1) year from the date of the
products original purchase by the
first consumer purchaser of the
product.
Consumer Accessories Ninety (90) days from the date
of the accessories original
purchase by the first consumer
purchaser of the product.
Consumer Products and The balance of the original
Use of Non-Motorola branded Products and
Accessories that are
Repaired or Replaced from the date returned to the
warranty or for ninety (90) days
Accessories. Defects or damage that result from the use of
Non-Motorola branded or certified Products or Accessories
or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by
someone other than MOTOROLA, BINATONE or its
authorized service centers, are excluded from coverage.
consumer, whichever is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this Warranty.
General information
27
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts,
are excluded from coverage.
warranty card was included in your box, a completed
warranty card showing the serial number of the Product; (d)
a written description of the problem; and, most importantly;
(e) your address and telephone number.
These terms and conditions constitute the complete
warranty agreement between you and BINATONE.
regarding the Products or Accessories purchased by you,
and supersede any prior agreement or representations,
including representations made in any literature publications
or promotional materials issued by BINATONE. or
representations made by any agent employee or staff of
BINATONE, that may have been made in connection with
the said purchase.
Communication Services. Defects, damages, or the failure
of Products or Accessories due to any communication
service or signal you may subscribe to or use with the
Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other
Information?
To obtain service or information, please call:
FCC, ACTA and IC regulations
US and Canada: 1-888-331-3383
FCC Part 15
You will receive instructions on how to ship the Products or
Accessories at your expense and risk, to a BINATONE
Authorized Repair Center.
This equipment has been tested and found to comply with
the requirements for a Class B digital device under Part 15
of the Federal Communications Commission (FCC) rules.
These requirements are intended to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt) which
includes the date, place and seller of the Product; (c) if a
28
General information
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation. Privacy of communications
may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria
for the amount of radio frequency energy that can be safely
absorbed by a user or bystander according to the intended
usage of the product. This product has been tested and
found to comply with the FCC criteria. Both the Handset may
be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user's
body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
•
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
This Class B digital apparatus complies with Canadian
ICES-003.
FCC Part 68 and ACTA
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the
back or bottom of this equipment contains, among other
things, a product identifier in the format US:
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may
General information
29
AAAEQ##TXXXX. This identifier must be provided to your
local telephone company upon request.
your telephone line, ensure the connection of this equipment
does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult
your telephone company or a qualified installer.
The plug and jack used to connect this equipment to
premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also
compliant. An RJ11 jack should normally be used for
connecting to a single line and an RJ14 jack for two lines.
See Installation Instructions in the User's Guide.
If this equipment is malfunctioning, it must be unplugged from
the modular jack until the problem has been corrected.
Repairs to this telephone equipment can only be made by the
manufacturer or its authorized agents. For repair procedures,
follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network,
the telephone company may temporarily discontinue your
telephone service. The telephone company is required to
notify you before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the
telephone company is required to inform you of your right to
file a complaint with the FCC. Your telephone company may
make changes in its facilities, equipment, operation, or
procedures that could affect the proper functioning of this
product. The telephone company is required to notify you if
such changes are planned.
The Ringer Equivalence Number (REN) is used to determine
how many devices you may connect to your telephone line
and still have them ring when you are called. The REN for
this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the
REN is 0.3). In most, but not all areas, the sum of all RENs
should be five (5.0) or less. For more information, please
contact your local telephone company.
This equipment may not be used with Party Lines. If you
have specially wired alarm dialing equipment connected to
30
General information
If this product is equipped with a corded or cordless handset,
it is hearing aid compatible.
Industry Canada
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation.
If this product has memory dialing locations, you may
choose to store emergency telephone numbers (e.g., police,
fire, medical) in these locations. If you do store or test
emergency numbers, please:
The term "IC: " before the certification/registration number
only signifies that the Industry Canada technical
specifications were met.
•
Remain on the line and briefly explain the reason for the
call before hanging up.
•
Perform such activities in off-peak hours, such as early
morning or late evening.
The Ringer Equivalence Number (REN) for this terminal
equipment is 0.0. The REN is an indication of the maximum
number of devices allowed to be connected to a telephone
interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that
the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical
specifications.
General information
31
Technical Specifications
RF frequency band 1921.536 MHz - 1928.448 MHz
Channels
5
Operating
5ºC to 45ºC
temperature
Telephone base
voltage
(AC voltage, 60Hz)
96 — 130 Vms
6VDC, 300 mA
Telephone base
voltage
(Adapter output)
Handset voltage
2.4V 500mAh Ni-MH battery pack
6VAC, 300mA
Charger voltage
(Adapter output)
32
General information
Manufactured, distributed or sold by Binatone
Electronics International LTD., official licensee for
this product. MOTOROLA and the Stylized M Logo
are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC. and are used
under license. All other trademarks are the
property of their respective owners.
© 2011 Motorola Mobility, Inc. All rights reserved.
Version 1.0
Printed in China
|
