Telephone setup continued
Security code (continued)
Installation: First-time battery charging
WARNING: The rechargeable battery pack must be fully charged
Return
to Menu
Antenna
before you use your T7406 handset for the first time.
4. Press CHANGE to assign a security code to the handset.
Collar light
A
D
The display shows Enter Password.
To correctly charge a new battery pack and handset:
B
Display
5. Enter the six-digit password (default 000000).
6. Press OK. The display shows Press 6 digits
7. Enter the six-digit Security code that was assigned to the
base you are connecting to.
1. Charge the battery pack in the bat-
tery port at the back of the charger for a
minimum of 30 minutes.
T7406 Cordless Telephone
User Card
Display buttons
Feature
C
G
2. Install the battery pack onto the back
of the handset.
Memory and
line buttons
8. Press OK to accept the code.
The display shows 4. Set S.S. Code :
If you are assigning a handset to an existing base, your
handset is now connected to the system.
If you are assigning the first handset to a new base station
(which has no security code), continue with the following
steps:
9. When the displays shows 4. Set S.S. Code :, press NEXT
to get ready to send the security code to the base.
The display shows 5. Send S.S. Code.
10. Unplug the AC power adapter connected to the base,
and plug it back in again.
11. Within 15 seconds, press and hold the OK for five sec-
onds to send the security code to the base. The display
shows Send OK! and you hear a beep when the transfer
is successful.
Note: If the Security Code transfer fails, Send Error! dis-
plays. To correct this, repeat steps 10 and 11.
12. Press the Options button. The date and time displays.
3. Put the handset into the handset port
on the charger. When the contacts
touch correctly, the handset charge
indicator (left LED) lights up red. The
battery pack is fully charged when the
LED turns green (three hours).
Handset Card
E
Release
F
Hold
H
N
ABC
JKL
TUV
DEF
1
4
7
2
5
8
0
3
6
9
Headset port
GHI
MNO
PQRS
WXYZ
4. Place the spare pack into the back
battery port. The battery pack indicator
light (right LED) turns red while it
charges. The spare battery pack is fully
charged in approximately 12 hours
(LED turns green).
#
M
Lanyard
anchor
J
Microphone
Volume
control
I
Options
Dialpad
L
button/Mute
Telephone setup
Each handset must be registered to a base by sharing an identi-
cal security code. A base can support up to three independent
handsets. Each handset assigned to a base station must have a
unique Set ID (1, 2 or 3).
K
O
© 2002 Nortel Networks
P0942259 03
Printed in Taiwan
Battery
Pack
Handset options
To access the following handset options:
When viewing the back of the base station, the TCM/RJ-11 jacks
from left to right correspond to the handset ID # 1, 2, and 3.
1. Press the Options button.
Your T7406 cordless telephone
Your T7406 cordless telephone
Handset ID #
For each new handset, you must first configure the handset ID #
to identify the handset to the base station:
2. Press SHOW.The display shows 1. Ring Type.
3. Press NEXT until the display shows you the selection.
4. Follow the directions in each section.
5. Press QUIT to exit the menu.
A
F
Antenna collar light
® Release button
Flashes to signify an incoming call.
Ends an active call.
1. Press the Options button.
2. Press SHOW.
B
C
Display
G
H
≤ Feature button
Starts or cancels a feature.
Ring type
To select a ring type for your handset:
Shows the time and date, call information, handset
status icons, and guides you through features and
options menus.
3. Press NEXT until the display shows 6. Handset ID.
4. Press SHOW. The display shows the current Handset ID.
5. If you want to change the ID number, press CHANGE.
The display shows Enter Password.
6. Enter the six-digit password (default 000000)
7. Press OK. The display shows Press Digit 1-3.
8. Press the appropriate digit on the dialpad.
9. Press OK to accept the configuration.
1. When the display shows 1. Ring Type, press SHOW.
2. Press CHANGE to listen to the different types of ring.
Note: There is also a Ringer Off setting.
3. Press OK to accept the ring type of your choice.
The display shows the ring type number you chose.
≥ Hold button
Places calls on hold.
Display buttons
I
The labels for display buttons appear on the second
line of the display. Display button functions change
with each feature.
Dialpad
J
K
Microphone
Volume level
To select the ringer volume level for your handset:
Refer to the Installation manual for instructions about how to
change the password.
Options button/Mute
Options Lists=7
Feature message
Display button label
SHOW QUIT
1. Press NEXT until the display shows 2. Ringer Volume.
2. Press SHOW. The display shows Press Volume bar.
3. Press the volume bar on the left side of the handset to
adjust the ringer volume.
4. Press OK to accept the ringer volume.
The display shows 2. Ringer Volume.
Answers calls, mutes the microphone on an active
call, and accesses the Options list on the display.
Display icons
Security code
If your installer has already set up a base, obtain the security
code and follow steps 1 to 8, inclusive.
L
Volume control
Display button
Adjusts the handset, headset, and ringer volume.
If you need to assign a security code to the base, follow all the
steps in this section.
D
E
Memory and line buttons
These buttons provide one-touch dialing, feature
operations, line access or answering a line.
M
N
O
Lanyard anchor
For attaching a wrist strap.
Lock Handset
To lock the buttons on the handset to prevent unintentional
button presses:
To assign a security code to a handset follow steps 1 to 8:
1. Press the Options button.
2. Press SHOW.
3. Press NEXT until the display shows 4. Set S.S. Code :.
Headset port
For connecting a headset.
Handset card
1. Press NEXT until the display shows 3. Lock Handset.
2. Press OK. The display shows Handset Locked.
3. To release the handset, press ®, then press •.
Write the button function on this card.
Continued...
Battery pack
|